Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Wildgame R12I20-9
- Page 1 User’s Manual...
-
Page 2: Battery Installation
Battery Installation Open the door on the right With the camera facing up, of the camera and PULL the open the compartment door. tabtowards you. Push the battery latch up to unlock. At the same time grab the battery compartment out. Page 1... - Page 3 Make sure to insert the Load SD memory card (up to AA-cell batteries based on 32GB) into the SD CARD slot the direction labeled on the with the connectors facing inside of each compartment. down. Match minus “-” sign with the marked negative on the battery and the plus “+”...
- Page 4 Power OFF: To turn the unit ON press and To turn the unit off, first wake release the power button. up the LCD screen and then depress and hold the power button until the LCD turns off. POWER RESET POWER RESET Check the battery level icon to ensure the batteries just...
- Page 5 Reset Reset button located next to the battery compartment. Push button to reset settings back to factory settings. POWER RESET Page 4...
-
Page 6: Test Mode
Test Mode LCD Ready Mode: The camera will automatically enter Ready Mode if a button is not pressed for greater than 30 seconds. The status lights will illuminate for a total of 2 minutes. PIR LED Status Light: During the first 2 minutes of Ready Mode, the red light will illuminate when a PIR event is triggered. -
Page 7: Power Save
Power Save After 30 seconds without any buttons being pushed, the LCD will turn off and camera enters into Power Save or Ready Mode. The LCD screen can be awakened by pressing the Power button briefly. NOTE: The LCD will not “wake up” when camera is writing to memory. POWER RESET Page 6... -
Page 8: Setting Time
Setting Time To change date and time, start by pressing and release the OK button to set the hour. Press the up or down navigation button to go up or down in sequence. When the hour is set, repeat steps 1 and 2 to set the minutes. Page 7... -
Page 9: Setting Date
Setting Date Press the OK button after setting the minute to change the Day. Press the up or down navigation button to go up or down in sequence. When the DAY is set, repeat steps 1 and 2 to set the Month and Year. Page 8... - Page 10 Location Save the location of the area the Repeat steps 1 and 2 to set camera was installed. This is for the rest of the characters. your reference and is optional. If you Press the right navigation do not wish to name your location button to skip spaces and skip to the next step.
- Page 11 PIR Mode PIR Active Press the OK button while Press the OK button while PIR Mode is selected. The PIR Active is selected. The highlighted option will be highlighted option will be blinking. blinking. Press the left or right Press the left or right navigation button to move to navigation button to move to different options.
-
Page 12: Pir Sensitivity
PIR Sensitivity Exposure Press the OK button while Press the OK button while PIR Sense is selected. The Exposure is selected. The highlighted option will be highlighted option will be blinking. blinking. Press the left or right Press the left or right navigation button to move to navigation button to move to different options. - Page 13 Still Res. Video Res. Press the OK button while Press the OK button while Resolution is selected. The Picture is selected. The highlighted option will be highlighted option will be blinking. blinking. Press the left or right Press the left or right navigation button to move to navigation button to move to different options.
-
Page 14: Image Stamp
Delay Image Stamp Press the OK button while PICTURES DISPLAY: Delay is selected. The highlighted option will be blinking. 087°F 08:15PM 11-12-2011 0200 A- Temperature Press the left or right B- Time navigation button to move to C- Date different options. Press the D- Moon Phase OK button to save the setting. - Page 15 Mounting When mounting to a tree, first When mounting to a T-Post, remove the clip from one end first attach the T-Post of the strap so you can slide bracket to the camera. the strap through the slots located on the back of the camera.
- Page 16 There is also a standard 1/4”-20 tripod connector. Page 15...
- Page 17 Important The directions as contained herein assume that you are using a Microsoft operating system and not Linux or a Mac-based operating system. Even said, there may be slight variations in your process based on the specific version of the operation system that you are using as well as the predefined user preference for each computer.
-
Page 18: Retrieving Images
Retrieving Images (SD Card Reader) Remove SD card and use card reader left of your screen and select “Computer”. The summary view will then be illustrated A. First, remove the SD Card from the on the right hand side of the window where camera unit itself by pressing on it to where by the “Devices with Removable Storage”... -
Page 19: Format Sd Card
Format SD Card SDXC CARDS ARE NOT SUPPORTED Having trouble with your SD card? Try this. 1. Connect the SD card to your computer. If your computer has an SD card slot you can insert the SD card directly into the port. NOTE: If you are using a MicroSD card, you will need an adapter to allow it to fit into standard SD card ports.