Related Manuals for Galaxy Equipment 177GMIX30
Summary of Contents for Galaxy Equipment 177GMIX30
- Page 1 User Manual User Manual Planetary Mixers User’s Manual 8/2021 177GMIX30 Please read the manual thoroughly prior to equipment set-up, operation, and maintenance. - 1 -...
-
Page 2: Table Of Contents
User Manual Index Parts Overview ............... 3 Standard Accessories ............ 4 Operation Instructions ........... 4 Mixer Capacity Chart ............. 5 Troubleshooting ............. 6 Circuit Diagram .............. 6 Figure 1 Axle Diagram ........... 7 Figure 2 Gear Axle Diagram .......... 8 Figure 3 Gear Axle I Diagram ........ -
Page 3: Parts Overview
User Manual Parts Overview ITEM DESCRIPTION Screw M6*45 Top Cover Two Axle Cover Center Axle Cover Screw M8*25 Ring Bearing Cover Body Spiral Bearing 6205 Motor Rotor Stator of Motor Motor Switch-A Motor Switch-B Rear Bearing Cover Rear Cover Screw M6*45 Stand Bowl’s Board Cable Joint... -
Page 4: Standard Accessories
User Manual Standard Accessories Item Description Flat Beater Dough Hook Whisk Bowl NOTES: • Any agitator is easily installed by simply raising it onto the mixing axle, and the rotating it clockwise on the shaft until it locks into place. To remove, raise the agitator on the shaft until it clears the lock and then rotate counter-clockwise and lower. -
Page 5: Mixer Capacity Chart
User Manual Mixer Capacity Chart Maximum Bowl Capacity Product Agitator and Speed 10 Qt. / 20 Qt. Bread and Roll Dough - 60 % AR Dough Hook - 1st only 5 lb. / 20 lb. Heavy Bread Dough - 55% AR Dough Hook - 1st only 3 lb. -
Page 6: Troubleshooting
User Manual Troubleshooting Trouble Possible Causes Solution The axles can’t work when Poor contact of the electrical equip- Check the Plug operating the machine ment The mixing bowl is out of position Moving direction is not correct Change Leaks oil Sealing washer is damaged Change Difficult to move the bowl up and down... - Page 7 User Manual Axle Diagram ITEM DESCRIPTION Baffle Roller Spring Engager Gear Ring Dividing Ring Joint Gear Bearing Ring Joint Bearing Ring Joint Gear 1 Ring Bearing (6206) Oil Seal (Pd45*52*10) Sleeve Axle Bearing (6205) NOTES: • Be sure to install in correct position (see Figure 2-1) and lubricate all of the pins in the sleeve drive when assembling.
- Page 8 User Manual Gear Axle Diagram ITEM DESCRIPTION Bearing (6203) Gear Axle Sleeve High Speed Gear Low Speed Gear Bearing 6203 Plate NOTES: • At the center in the shaft unit. To the above is the gear shaft and gear shaft I. (see Figure 3-1) •...
- Page 9 User Manual Gear Axle I ITEM DESCRIPTION Bearing (6201) Gear Axle Key (5*14) Gear Stop Ring Bearing (6201) NOTES: • C-type stop ring (5) has to be fixed when reassembling - 9 -...
- Page 10 User Manual Turning Plate & Mixing Axle Diagram ITEM DESCRIPTION Screw (M6*35) Turning Plate Ring Safety Net (Locomotion) Safety Net (Immobility) Inner Gear Screw Planetary Gear Bearing (6204) Bearing (6206) Oil Seal (Pd35*56*12) Mixing Axle - 10 -...
- Page 11 User Manual Lifting Unit ITEM DESCRIPTION Bowl’s Screw Ring Scew M5*12 Gasket Arm’s Upper Board Guide Post Plate Scew M8*20 Flat Plate Gasket Screw M8*20 Arm’s Lower Board Plastic Ball Handle Flange Sleeve Handle Crank Small Shaft of Pull Rod Pull Rod Screw M12*45 Handle Hanging Shaft...
- Page 12 User Manual Fork & Speed Shaft ITEM DESCRIPTION Axle Spring Shaft Fork Eccentricity Knot Steel Ball Speed Spring Speed Block Screw Shaft Handle NOTES: • The speed selector/shifting mechanism is designed for simplicity and reliability. It features three mixing speeds. •...