Do you have a question about the Sitescan D-10 and is the answer not in the manual?
Questions and answers
lenre
March 19, 2025
how do you save your a peak on the d10 machine
1 comments:
Mr. Anderson
March 19, 2025
To save a peak on the Sonatest Sitescan D-10 machine, press the button to enter freeze mode, which holds an echo for evaluation. Press the button again to enter peak mode, which holds and updates all echoes on the display during inspection. In this mode, an envelope or echo dynamic pattern is drawn on the screen, allowing the peak signal to be located. A box labeled "PEAK" will be highlighted below the graticule to indicate this mode is active.
Sitescan D-10 & D-20 User’s Guide ~ Contents Sitescan D-10 & D-20 User’s Guide ~ Contents Contents Contents How to Use How to Use This User’s Guide This User’s Guide ....................................1 1 Typog Typographi raphical Conven cal Conventions tions ..
Section 5: Flaw Testing gives guidelines on performing flaw testing with examples of how to calibrate the Sitescan D-10 & D-20 and how to set up the unit for DAC and TCG and how to use the A-Scan storage facilities.
Competent training of the instrument operator. • This user’s guide provides instruction in the basic operation of the Sitescan D-10 & D-20 flaw detector. In addition to the methods included, many other factors can affect the use of this flaw detector. Specific information regarding these factors is beyond the scope of this manual.
Sitescan D-10 & D-20 User’s Guide ~ Disclaimers and Notices More specific information about operator training, qualification, certification and test specifications can be obtained from technical societies, industry groups and government agencies. 2.4 Testing Limitations In ultrasonic testing, information is obtained only from within the confines of the sound beam as it propagates into the test material.
Sitescan D-10 & D-20 User’s Guide ~ Disclaimers and Notices response. For these reasons, calibration should be performed on test blocks made of the same material as the test piece with artificial discontinuities within the range of size and depth in the material to be detected. The user is again cautioned to refer to reference books which are beyond the scope of this manual.
Sonatest Limited in connection with the use, features and qualifications of the Sitescan D-10 & D-20 are based on tests believed to be reliable, but the accuracy or completeness thereof is not guaranteed. Before using the product you should determine its suitability for your intended use based on your knowledge of ultrasonic testing and the characteristics of materials.
Sitescan D-10 & D-20 User’s Guide ~Quick Start 3 Quick Start 3.1 Front Panel The main control on the front of the unit is the scroll-wheel that is used to navigate through the menus and to adjust parameters this, along with the key in the middle of the wheel...
Page 14
Sitescan D-10 & D-20 User’s Guide ~ Quick Start These buttons move the highlighted cursor along the top of the screen left and right to the sub menu to be selected, they are also used to make large increment changes to a selected parameter. These are momentary buttons with no repeat.
Page 15
Sitescan D-10 & D-20 User’s Guide ~Quick Start Pressing the key again invokes the Hold mode that captures the current A- Scan in white allowing a comparison to be made with the live A-Scan that is shown in green. When this mode is selected a box is highlighted showing as shown below:...
Page 16
Sitescan D-10 & D-20 User’s Guide ~ Quick Start The full screen button is used to toggle between showing the A-Scan on the full display and showing it with the menus and parameter boxes as shown below: Full display is useful for maximising the size of the A-Scan while performing inspections.
Page 17
Sitescan D-10 & D-20 User’s Guide ~Quick Start This button selects the help menu which overlays the display. The help menu explains how the Sitescan D-10 & D-20 operate with a choice of three options: button : Basic operation rpbo button...
Sitescan D-10 & D-20 User’s Guide ~Quick Start 3.2 Flaw Detection Perform the following steps to establish a basic flaw detection mode for the Sitescan D-10 & D-20. Units shown are in inches. For inch units, select from the menu and...
Page 20
Sitescan D-10 & D-20 User’s Guide ~ Quick Start The Sitescan D-10 or D-20 is now configured for basic flaw detection. Using an appropriate calibration block, adjust the parameter to establish the correct sensitivity. Adjust GAIN other parameters as necessary to optimize the calibration. For more in-depth features of the Sitescan D-10 &...
Need help?
Do you have a question about the Sitescan D-10 and is the answer not in the manual?
Questions and answers
how do you save your a peak on the d10 machine
To save a peak on the Sonatest Sitescan D-10 machine, press the button to enter freeze mode, which holds an echo for evaluation. Press the button again to enter peak mode, which holds and updates all echoes on the display during inspection. In this mode, an envelope or echo dynamic pattern is drawn on the screen, allowing the peak signal to be located. A box labeled "PEAK" will be highlighted below the graticule to indicate this mode is active.
This answer is automatically generated