Related Manuals for Arestech BPC-3080
Summary of Contents for Arestech BPC-3080
- Page 1 User Manual BPC-3080 Fanless Compact Embedded Box PC with 8 Generation Whiskey Lake-U Quad-core Intel® Core™ i5 processor...
- Page 2 User Manual Record of Revisions Version Issue Date Descriptions Made By 2021/07/27 First Release Derek...
- Page 3 Product Warranty (2 Years) Arestech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the invoice date. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Arestech, or which have been subject to misuse, abuse, accident, or improper installation.
- Page 4 User Manual Safety Instructions Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
- Page 5 User Manual Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage: 1. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on. 2.
-
Page 6: Table Of Contents
User Manual Contents Chapter 1. General Introduction ..................7 1.1 I/O Arrangement ..................... 7 1.2 Internal Interfaces ....................12 1.3 Mechanical Dimensions ..................14 Chapter 2. System Setup ..................... 15 2.1 Power Installation Procedure ................15 2.2 Installing 2.5" HDD and Swappable HDD Bracket ..........17 2.3 Installing Memory and Internal Expansion Device .......... -
Page 7: Chapter 1. General Introduction
User Manual Chapter 1. General Introduction 1.1 I/O Arrangement GPIO Power input 9-36v Power Button Com 2/3/4 USB 2.0 HDMI Mic In COM1 USB3.1 Gen 2 Line Out ◼ Power Button Press this button to turn on the system. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. - Page 8 User Manual Definition Vin+ (9-36V DC) ◼ HDMI Port This port can be connected to an HDMI monitor. 2 x HDMI 1.4 ports support a maximum resolution of 4096 x 2304 @ 24Hz. Definition Definition TMDS Data2+ TMDS Data2 Shield TMDS Data2 - TMDS Data1+ TMDS Data1 Shield...
- Page 9 User Manual 10/100BASE-T: Definition Pin Definition TX_D0+ TX_D0- RX_D1- RX_D1+ 1000BASE-T: Definition Pin Definition TX_D0+ BI_D2- TX_D0- RX_D1- RX_D1+ BI_D3+ BI_D2+ BI_D3- Activity/Link LED Status Description No Link Blinking Data Activity Link SPEED LED Status Description 10Mbps connection Green 100Mbps connection Orange 1Gbps connection...
- Page 10 User Manual ◼ USB 3.1 Gen 2 Port Definition USB- USB+ StdA_SSRX- StdA_SSRX+ GND_DRAIN StdA_SSTX- StdA_SSTX+ Basically, USB3.1 Gen 2 supports 900mA @ 5 V ◼ COM 1 (RS-232/422/485); COM 2 / 3 / 4 (RS-232) Users can change the configuration of COM1 by using BIOS setup utility. RS-232 RS-422 RS-485...
- Page 11 User Manual ◼ Digital I/O Ports (Optional) GPO_1 GPO_2 GOP_3 GPO_4 GOI_1 GOI_2 GOI_3 GOI_4 SMB_CLK SMB_DATA 11 +5V Guide: 1. DI ports have default high (3.3V) voltage. Users have to input a low (GND) voltage to give a trigger signal. 2.
-
Page 12: Internal Interfaces
User Manual 1.2 Internal Interfaces ◼ SATA Connector Definition ◼ SATA Power Connector Definition +12V ◼ mini-PCIe Slot 1 x Full-size Mini PCIe with SIM slot (PCIe x1 + USB2.0), supporting 3G/4G module mini cards. - Page 13 User Manual ◼ M.2 Slot 1x 2230 M.2 E-Key (PCIe x1, USB 2.0 for Wi-Fi modules.) 1 2280 M.2 M-Key (PCIe x4, SATA 6Gb/s)
-
Page 14: Mechanical Dimensions
User Manual 1.3 Mechanical Dimensions... -
Page 15: Chapter 2. System Setup
1. Connect the male end (Phoenix connector) of the power cord to the DC input connector of BPC-3080 and lock it up. 2. Connect the 3-pin male plug of the power cord to an electrical outlet. 3. Connect the Phoenix connector terminal to the system's power input connector. - Page 16 CONNECTOR IS PLUGGED IN WITH CORRECT DIRECTION. ◼ Connect Keyboard and Mouse Connect the mouse and keyboard to the USB connectors of BPC-3080. ◼ Turn on Power The power button is located at the right side of the front cover of the box pc.
-
Page 17: Installing 2.5" Hdd And Swappable Hdd Bracket
User Manual 2.2 Installing 2.5" HDD and Swappable HDD Bracket ◼ Step 1: Unfasten the 8 screws on the chassis and open the bottom cover. ◼ Step 2: Unfasten the SATA cable and SATA power cable on the HDD/SSD. - Page 18 User Manual ◼ Step 3: Unfasten the 4 screws on the HDD/SSD bracket. ◼ Step 4: Install another HDD/SSD and fasten all screws. ◎ NOTE: THE BRACKET ONLY SUPPORTS 7MM HDD/SSD.
-
Page 19: Installing Memory And Internal Expansion Device
User Manual 2.3 Installing Memory and Internal Expansion Device This box pc provides two 260-pin DDR4 (Double Data Rate 4) SO-DIMM slots, supporting dual channel DDR4 SDRAM only. ◼ Step 1: The notch on the SO-DIMM should be lined up with the slot key. ◼... -
Page 20: Installing Mini-Pcie Card And M.2 Device
User Manual 2.4 Installing mini-PCIe Card and M.2 Device Expansion Slots (mini-PCIe ,M.2 E Key 2230, and M Key 2280) There is 1x mini-PCIe slot, 1x M.2 E key 2230 slot, and 1x M key 2280 slot on this motherboard. ◼... - Page 21 User Manual ◼ Installing An Expansion Card 1. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
-
Page 22: Chapter 3. Bios Setting
User Manual Chapter 3. BIOS Setting ® he BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports, and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system. -
Page 23: Main
User Manual 3.1 Main This section (Main screen) displays the system overview. ◎ NOTE: TO CLEAR CMOS, PLEASE REMOVE THE BATTERY IN THE RED FRAME TO SHORT THE TWO PINS. -
Page 24: Advanced
User Manual 3.2 Advanced... -
Page 25: Cpu Configuration
User Manual 3.2.1 CPU Configuration SW Guard Extensions (SGX) ◼ This item allows users to enable, disable, or software control SW Guard Extensions. The default value is [Software Controlled]. ® ◼ Intel Virtualization Technology ® This item allows users to enable or disable Intel Virtualization Technology. -
Page 26: Trusted Computing
User Manual 3.2.2 Trusted Computing ◼ Configuration Security Device Support Select [Enabled] to activate TPM support feature. Options available: [Enabled] and [Disabled]. Default setting is [Disabled]. Current Status Information This displays current TPM status information. -
Page 27: Sata And Rst Configuration
User Manual 3.2.3 SATA and RST Configuration ◼ SATA Mode Selection ® ® This item allows users to select AHCI or Intel RST Premium with Intel Optane System Acceleration. -
Page 28: Hardware Monitor
User Manual 3.2.4 Hardware Monitor ◼ CPU Fan Fail Warning This item allows users to enable or disable the CPU Fan Fail Warning. System Fan Fail Warning ◼ This item allows users to enable or disable the System Fan Fail Warning. ◼... -
Page 29: It8786 Super Io Configuration
User Manual 3.2.5 IT8786 Super IO Configuration Serial Port 1 Configuration ◼ This item allows users to enable or disable the COM 1 and to select COM 1 mode as RS232, RS 485, or RS 485/422. ◼ Serial Port 2 Configuration This item allows users to enable or disable the COM 2. -
Page 30: Rtc Wake Settings
User Manual 3.2.6 RTC Wake Settings ◼ Wake System from S5 This item allows users to enable or disable the Wake System from S5. -
Page 31: Csm Configuration
User Manual 3.2.7 CSM Configuration ◼ CSM Support This item allows users to enable or disable the CSM Support. ◼ LAN PXE OpROM This item allows users to enable or disable the LAN PXE OpROM. ◼ LAN EFI Drive This item allows users to enable or disable the LAN EFI driver. ◼... - Page 32 User Manual ◼ CSM Support Never support CSM. ◼ LAN EFI Driver This allows users to select [Enabled] or [Disabled].
-
Page 33: Chipset
User Manual 3.3 Chipset ◼ VT-d This item allows users to enable or disable the VT-d. The default value is [Enabled]. ◼ DVMT Pre-Allocated This item allows users to set DVMT as [64M], [128M], [256M], or [512M]. The default value is [64M]. ◼... - Page 34 User Manual ◼ ERP Lowest Power State Mode This item allows users to enable or disable the ERP Lowest Power State Mode. The default value is [Disabled]. ◼ Restore AC Power Loss (AT/ATX Power setting) This item allows users to set Restore AC Power Loss as [Power On], [Power Off], or [Last State].
-
Page 35: Security
User Manual 3.4 Security Administrator Password ◼ Set or change the password for the administrator account. Only the administrator has the authority to change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password. ◼... -
Page 36: Boot
User Manual 3.5 Boot ◼ Full Screen LOGO Show This item allows users to enable or disable the Full Screen LOGO Show. The default value is [Disabled]. ◼ Boot Option #1~#N This item allows users to set the system boot order. ◼... -
Page 37: Exit
User Manual 3.6 Exit ◼ Save Changes and Reset When you select this option, the following message will pop out “Save configuration changes and reset?”. Select [OK] to save the changes and exit the UEFI SETUP UTILITY. ◼ Discard Changes and Reset When you select this option, the following message will pop out “Reset without saving?”.
Need help?
Do you have a question about the BPC-3080 and is the answer not in the manual?
Questions and answers