Advertisement
2. ASSEMBLY & OPERATING
2.1.
ASSEMBLY. Unpack carton and assemble the fan as follows:
2.1.1. Remove the locking nut (fig 1. 1) from the centre of the fan
2.1.2. Fitting the rear fan guard. Identify the rear fan guard by the location holes in the centre plate (fig 1.2) and place the guard over the fan
spindle and fit onto the three location pins (3).
2.1.3. Replace and secure the back guard with locking nut (1).
2.1.4. Fitting the fan. Slide the fan onto the motor shaft until it comes to rest against the pin which is pushed through the shaft. Rotate the fan
slightly until the pin comes to rest in the shallow groove in the back of the fan. Now take the large plastic circular lock nut and thread it
onto the end of the motor shaft by turning it anticlockwise. Hold one of the fan blades with one hand and tighten the nut down onto the
fan to hold it in place.
2.1.5. Fitting the front fan guard to the rear fan guard. The front guard has a plastic rim attached to it which enables it to hook over the top of
the rear guard (fig 2.A); snap together at the sides, and screw fix at the bottom (fig 2.B). On the inside of the front guard at the top you will see
2 small square plastic lugs. Hook these lugs over the rim of the rear guard and push the front guard on as far as it will go at the bottom.
2.1.6. Hold the two guards together at either side and gently squeeze until they snap together.
2.1.7
Now take the small plastic fixing lug and press it into place over the screw fixing hole at the bottom of the front guard. Place the securing
screw through the plastic lug and tighten it up so that the lug fits snugly against the back of guard rim (B).
2.1.8. Check that the guard has been assembled correctly and that the fan will turn freely before plugging into the mains.
If all is correct the fan is now ready to use.
2.2.
FAN OPERATION.
WARNING! Ensure you read, understand and apply the safety instructions in part 1 before using the fan.
2.2.1. Use handle (fig 3.1) to carry the fan and place in a suitable location and plug into the mains power supply.
p
2.2.2. Press button “1” (fig 3. 2) for low fan speed operation, button “2” for medium fan output, and button “3” for high fan output.
To stop the fan press button “0”.
2.2.3. To make the fan oscillate, push down the oscillating knob (3) on top of the motor casing.
To stop the fan oscillating, pull the knob up.
2.2.4. To adjust the fan up or down, loosen the swivel knob (4) position the head accordingly and tighten knob.
fig 1
3. PARTS LIST
SDF12H & SDF16H
ITEM PART NO
PART NO
1
SDF12H01
SDF16H01 GRILLE COVER
2
SDF12H02
SDF16H02 FRONT GRILLE
3
SDF12H03
SDF16H03 SPACER
4
SDF12H04
SDF16H04 BLADE LOCK NUT
5
SDF12H05
SDF16H05 FIXING NUT
6
SDF12H06
SDF16H06 M4 SCREW
7
SDF12H07
SDF16H07 PLASTIC RING
8
SDF12H08
SDF16H08 BLADE
9
SDF12H09
SDF16H09 GRILLE LOCK NUT
10
SDF12H10
SDF16H10 REAR GRILLE
11
SDF12H11
SDF16H11
12
SDF12H12
SDF16H12 MOTOR
13
SDF12H13
SDF12H13 MOTOR COVER
14
SDF12H14
SDF16H14 CLUTCH KNOB
15
SDF12H15
SDF16H15 CAPACITOR
16
SDF12H16
SDF16H16 LINK ROD
17
SDF12H17
SDF16H17 HINGE
18
SDF12H18
SDF16H18 U PLATE
19
SDF12H19
SDF16H19 ADJUSTMENT KNOB
20
SDF12H20
SDF16H20 BODY
21
SDF12H21
SDF16H21 PIANO SWITCH
22
SDF12H22
SDF16H22 BASE
23
SDF12H23
SDF16H23 TERMINAL BLOCK
24
SDF12H24
SDF16H24 CORD CLAMP
25
CS 2.5M2C BLK
Declaration of Conformity
DESK FAN Models SDF12H, SDF16H
EN 60335-2-80
89/336/EEC Electromagnetic Compatibility
73/23/EEC Low Voltage Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: Call us for a copy of our latest catalogue on 01284 757525 and leave your full name and address including your postcode.
fig 2
DESCRIPTION
MOTOR BRACKET
POWER CORD
We, the sole importer into the UK, declare that the products listed below are in conformity with the following EEC standards and directives
The construction file for these products are held by the Manufacturer and may be inspected on request by contacting
Jack Sealey Ltd
Signed by Mark Sweetman
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500
01284 703534
fig 3
Original Date:-
Issue Date:-
Version No:-
Date Modified:-
For Jack Sealey Ltd.
Sole importer into the UK
22nd November 2000
of Sealey Power Products
E-mail: sales@sealey.co.uk
SDF12H, SDF16H -(1086) - (1) 201100
201100
201100
1
1st Issue
Advertisement
