Open House ChannelPlus H721 Manual

ChannelPlus Video Camera
The H721 video cameras
J-boxes. The H721 must be used with one of its companion channel injectors
(H511HHR or H511BID). When used with an H511, video received from the
H721 is used to create a new channel to add to existing television channels.
The H721 is connected to the H511 by a single run of CAT-5 wire and does not
need to be separately powered. The camera mount is weather-resistant and
comes with a standard single-gang gasket. The brass cover-plate may be
painted to match a house color.
Two models are available:
Model H721
Black & White, 0.3 lux, 3.6 mm lens
Model H721C
Color, 6 lux, 3.6 mm lens
Note: The H721 is not a standalone video camera
Use only with an H511 channel injector.

Typical Installation

Connect the H721 camera using only
1 Terminate cable with a CAT-5 jack and connect to the H511 using
supplied RJ45 jumper. (Also see example H628 manual).
2 Wire camera or wall plate directly to the 8 position terminal block
matching the CAT-5 wire colors to the colors on the terminal block.
Insert wires and tighten screws.
1
2
CAT-5 video
Channel Injector
H511HHR
or
H511BID
Maximum CAT-5 run:
H721 to H511 300 feet
H721C to H511 100 feet
H721

(rear view)

Insert wire into terminal block and tighten screws. Use the color bar to match
wire colors. The color bar has two rows, one for CAT-5 and one for quad wire:
- For CAT-5 wire, remove the default resistor and use all 8 wires.
*
- For quad wire , leave default resistor in place and match four color wire.
*
The H721/H721C was designed to work with CAT-5 wiring. Although the system will function with
quad wire, CAT-5 delivers the highest quality picture. CAT-5 allows the use of an automatic line
length sensor and picture compensator. Quad wire does not take advantage of this enhancement.
Specifications:
typical @ 25 C ± 5 C
Model
Image format
Resolution, horizontal
Resolution
Minimum illumination
Signal to Noise ratio
AGC
Lens
Lens viewing angle
White balance
Electronic shutter speed
Maximum distance to H511
are solid state cameras designed to fit standard single gang
one method:
Program
CATV
Output
/Ant Power
Connect antenna or incoming
cable to H511 input.
Connect H511 output to splitter
or distribution panel input.
(See H511 manual)
O O
H721 H721C
EIA (Black & White ) NTSC (Color)
525 lines
525 lines
350 lines 350 lines
0.3 lux 6 lux
>45 dB >45 dB
Yes Yes
3.6mm F2.0 3.6mm F2.0
78 O 78 O
automatic automatic
1/60 to 1/50000 second 1/60 to 1/50000 second
300 feet 100 feet

Installing the Camera

The H721 is designed to be mounted in a single-gang J-box using the supplied gasket.
Power the H511 last -
make all cable and
CAT-5 connections first.
Locating the Camera
The camera 'looks' straight out from the cover-plate. For a front door application,
place the camera lens 66 inches off the ground, adjacent to the door.
Painting the Cover-Plate
The brass cover-plate may be painted to match the house color. First, remove
the camera from the plate. Lightly sand the plate using 300-400 grit wet/dry
paper. Use a good quality metal primer that is rated for exterior use. Before
applying the primer, follow the manufacturers instructions for cleaning the plate.
Standard house paints may now be used.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Installation requirements:
FCC classifies this product under part 15 of its rules as a "television interface device".
Systems designed using television interface devices have the following legal requirements:
1) The modulated channel signal strength may not exceed 15.56dBmV at any television.
Federal Regulation 47CFR15.115(b)(1)(i).
2) If an antenna is used in the system, the modulated channel signal strength may not exceed
-51dBmV at the antenna input port.
For the Installer:
Any system you design must comply with these regulations. As the installer, you are
responsible. The H721 or H721C (when used with an H511) has the necessary characteristics
to comply with the above requirements as designed without additional accessories.
The H511HHR is suitable for use with an antenna or with CATV systems.
The H511BID is suitable for use with CATV systems only.
Run a line of CAT-5 wire from the
channel injector to the camera location.
Standard
single-gang
J-box
J-box

DECLARATION OF CONFORMITY

Federal Regulation 47CFR15.115(c)(4).
1
2
Prepare the CAT-5 wires by stripping
1" of outer sheath and 1/8" of
insulation. Insert wires into 8 position
terminal block and tighten screws.
Remember to wire through gasket.
3
Push camera into J-box and attach
using the two supplied screws.
6-32 X 1"
screw