ONWELL SM7-BT User Manual

User's Manual – Wireless Speaker Mic 7
Model: SM7-BT
Wireless Speaker Mic. 7, Heavy Duty, Rechargeable
Battery Powered, IP55, 3.5mm earpiece port
FCC ID: 2A2BD-SM7-BT
Product Overview:

No. Function No. Function
1 PTT 7 Status LED
2 Volume up 8 Function button
3 Volume down 9 Torch ON/OFF
4 Torch light LED 10 External earphone jack
5 Speaker / Microphone 11 Micro USB charging port
6 Power ON/OFF 12 Belt clip
Package contents:

Onwell GES-BTXM04, Bluetooth speaker microphone

USB chargeing cable

User's Manual

ONWELL Communication Limited. 20220905 – V1.0
Operation:

Power ON: Press power ON/OFF button

sound is heard and status LED
⑦
flashing blue.
Power OFF: Press power ON/OFF button

seconds until "Power off" sound is heard and status LED
flashes purple once.
Function Button: When the device is paired with a phone,

Function button can be used as answer/end/reject calls,
⑧
answer waiting call, switching between the active calls, and
dial to the last called number.
Torch light LED: Power ON device, press torch ON/OFF

button for approx. 1 second to turn on torch light LED
⑨
Press and hold for 2 seconds to turn off.
Volume control: Press volume up

adjust volume. The device will produce a tone when volume
reaches the minimum or maximum level.
External earphone: Open external earphone jack

cover, plug listen-only earphone with Ø3.5 2pole or 3pole
connector, loud speaker will automatically mute.
⑤
Status LED:

Status LED Indicator
Power ON Flashes Purple once, followed by flashing Blue
Charging Constant Red
Charge complete Constant Blue
Low battery Flashes Red during power ON or after RX/TX, with
beeping tone every 5 min
Pairing mode Flashes Red & Blue alternatively
Connection Flashes Blue one every 5 seconds
Unpaired or lost link Flashes Blue twice every 3 seconds
Paring Process for radio / phone

1. Make sure GES- BTXM04 is OFF, press & hold power button
switch on GES-BTXM04.
2. GES-BTXM04 is under pairing mode when the LED
BLUE alternatively and "Pairing" sound is heard.
3. Start Bluetooth function on your radio / phone.
4. Find the device name "BT-XM04" under Bluetooth device list and
connect it.
5. Pairing process is completed.
General specification:

Speaker
Microphone
, "Power on"
⑥
Protection grade
indicates purple, followed by
PTT key life
Talking Range
, hold for 2
⑥
Battery
⑦
Charging time
Operation temp.
Troubleshooting:

④.
Does not power ON
Cannot charge
or down button to
② ③
dust
⑩
Battery not holding
charge
Pairing issue
RX / TX issue
Unclear speech
to
⑥
flashes RED and
⑦
Battery charging

Ø36mm 8Ω 1W 89±3dB @1KHz (0.5m 1W)
-44±2dB@1KHz 0dB=1V/Pa
IP55 (dust cover properly closed)
≥1,000,000 Times
Bluetooth class 2, 10 meters
1500mAH Li-battery
About 3 hours (5V 500mA)
-20~50°C (-4~120°F)
Check if device is charged
Check connections to the device and wall outlet.
Check if the device's charging contacts are in contact
with optional desktop charging cradle.
Check charging status LED is on (RED)
⑦
Check if battery is fully charged.
Battery has definite service life; replace the battery
when it can't give sufficient run time even when it's
fully charged. Contact dealer to replace battery.
Cannot find device, power off radio/phone for 5
second, restart and search again for device
Check Bluetooth connection and pairing.
Check if water is trapped in grill, shake mildly to get
water out the speaker grill
⑤.