Related Manuals for SPORTSFIELD SPECIALTIES FieldSpec Drag Brush
Summary of Contents for SPORTSFIELD SPECIALTIES FieldSpec Drag Brush
- Page 1 FieldSpec® Synthetic Turf Maintenance Equipment Drag Brush OWNERS/OPERATING MANUAL Manufactured by Sportsfield Specialties, Inc Revision Date: 1/27/15...
- Page 2 CONGRATULATIONS Thank you for purchasing a FieldSpec® Synthetic Turf Maintenance product. This piece of equipment has been designed for specific use on in-filled, synthetic turf systems. To ensure years of dependable service this product has been designed and manufactured to the highest quality standards available in the industry today.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SAFETY INFORMATION……………………………… 4 SETUP…………………………………………………... 5 OPERATION……………………………………………. 6-8 SPECIFICATIONS……………………………………… 9 GENERAL ASSEMBLY & PARTS LIST……………… 10-12 REPLACEMENT PARTS INFORMATION…………… 13 WARRANTY INFORMATION………………………… 14-15 Revision Date: 1/27/15... -
Page 4: Safety Information
SAFETY INFORMATION DANGER Drag Brush is not designed to carry human occupants. Doing so is at the owner’s risk. The manufacturer of this unit is not responsible for injuries, permanent disabilities or fatalities that may be a result of this occurrence. CAUTION Wood crating contains nails and may splinter during removal of the synthetic turf maintenance unit. -
Page 5: Setup
SETUP Uncrating – The Drag Brush is packaged to ensure that damage does not occur during the shipping process. While the packaging is more than adequate to handle the normal bumps and shifts in loads during transit, in rare cases damage may occur. Upon receipt of the Drag Brush please inspect the packaging and unit to ensure that they are damage free. -
Page 6: Operation
OPERATION Lowering Extension Arms (IF APPLICABLE) – Once the Drag Brush is towed to the location of the synthetic infill turf field the Extension Arms must be carefully lowered. Each Extension Arm is held in the upright position by a locking pin which must be removed prior to lowering the arm, see Picture 3. - Page 7 Adjusting Brush Height – Once both extension arms have been lowered utilize the manual crank assembly to lower and raise the brush and tine assemblies, Picture 9. Prior to adjustment the brushes should be at a height of 2” to 3” off the ground depending on the infill depth and height of the synthetic fibers, see Picture 10.
- Page 8 Preparing the Drag Brush for Transport – Once grooming is complete the Drag Brush must be prepared for transport away from the synthetic infill turf field. To do this please remove the locking pin installed in Picture 7 and carefully lift the arm as shown in Picture 13. Once the arm begins to lift off the ground firmly grab the outside of the Extension Arm and pull upwards to the vertical locking position, reinsert pin as demonstrated in Picture 3.
-
Page 9: Specifications
SPECIFICATIONS Dimensions: With Extensions Overall Width: 82” 180” Length (Hitch to Rear): 85” 85” Height (Jack Handle to Ground): 35” 35” Approximate Weight: 240 lbs. 380 lbs. Construction Type: Steel Exterior Finish: TGIC Polyester Powder Coat Brush Specifications: Combo Poly Tines: 1/8”... -
Page 10: General Assembly & Parts List
GENERAL ASSEMBLY & PARTS LIST Revision Date: 1/27/15... - Page 11 GENERAL ASSEMBLY & PARTS LIST (CONT’D) Revision Date: 1/27/15...
- Page 12 WING ASSEMBLY & PARTS LIST Revision Date: 1/27/15...
-
Page 13: Replacement Parts Information
Additionally, operator based accidents with this equipment can and will happen resulting in an almost immediate need for replacement parts. Sportsfield Specialties, Inc. is committed to maintaining available inventory to ensure that these damaged part emergencies and “wear” based replacements can be responded to immediately. -
Page 14: Warranty Information
If the Equipment has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. If parts not made by Sportsfield Specialties have been used in connection with the unit, if, in the sole judgment of Sportsfield Specialties, Inc. such use affects its performance, stability or reliability. - Page 15 WARRANTY CARD TO BE COPIED AND MAILED OR FAXED TO (Please retain copy for your records): Sportsfield Specialties, Inc. Attn: Warranty Department P.O. Box 231 41155 State Highway 10 Delhi, NY 13753 (607) 746-8481 - Fax (888) 975-3343 - Phone...
Need help?
Do you have a question about the FieldSpec Drag Brush and is the answer not in the manual?
Questions and answers