KIDdesigns eKids iSF-12VM Quick Start Manual

Led light strip with remote

Hide thumbs

Table of Contents

Available languages

Quick Links

Download this manual

This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE).

This means that this product must be handled pursuant to European Directive 2012/19/EU in order to be recycled

or dismantled to minimize its impact on the environment.

For further information, please contact your local or regional authorities.

Electronic products not included in the selective sorting process are potentially dangerous for the environment

and human health due to the presence of hazardous substances.

WARNING:

• Do not ingest the battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button

cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.

• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the

product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of

the body, seek immediate medical attention.

• WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. REPLACE ONLY WITH

THE SAME OR EQUIVALENT TYPE. DO NOT DISPOSE OF BATTERIES IN THE HOUSEHOLD TRASH OR FIRE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Maintenance

It is important to keep the unit as dry and clean as possible. Unplug the unit, then clean the unit with a damp cloth. Stronger

cleaning agents, such as thinner or similar materials are not recommended, as they may damage the surface of the case.

Questions or Comments

For questions or comments regarding this or other eKids products, please visit our website: www.ekids.com

Getting Started:

Connect one end of the included USB power cable to the LED light strip, making sure Pin 1 on each are aligned.

Connect the other end of the USB cable to a powered USB port.

USB Adaptor

(not included)

Computer connected

to working outlet

Replacing the Batteries

ATTENTION: Batteries should only be installed by an adult.

The remote comes with a CR2025 battery already installed.

To replace the batteries at home, follow these instructions:

1. Follow the diagram on the back of the remote control to open the battery compartment door.

2. Install one CR2025 size battery into the compartment, making sure that the + and -

3. Close the battery compartment door.

For proper disposal of used batteries, please check with your local authorities.

KEEP USED BATTERIES AWAY FROM SMALL CHILDREN.

Adhesive Strip:

Important

• Apply power to test LED Light Strips before mounting.

• The backing tape on LED Light Strips is coated with a strong adhesive that is intended for a single

application only. Apply only when a lighting location is fully determined.

1. Remove the paper lining from the LED light strip to expose the adhesive.

2. Press firmly to mount the LED light strip on a dry, clean, flat surface.

Remote Control

Brightness

RGB Color Modes

Remote Functions:

Use the remote control to adjust colors, brightness, and light modes.

Colors: Press the color buttons to cycle through hues of Red, Green, and Blue. Press the W Button for white light.

Brightness: Use the Brightness Buttons to select High or Low.

Light Modes: Flash, Strobe, Fade, Smooth

Important Safety Information:

Before installing, read and follow all precautions, including the following:

CAUTION: RISK OF ELECTRIC SHOCK OR BURNS - USE IN A DRY LOCATION ONLY

WARNING: The LED strip must be unplugged when making any modifications to the device.

LED Light Strip Handling:

• Do not place in reach of children.

• Do not stare directly into LED lights when illuminated.

• Always disconnect power supply before cutting/connecting LED Light Strips.

• Do not expose LED Light Strips' to direct or indirect moisture.

• For indoors use only.

• For optimum performance connect to a 5v 1A USB adapter.

• Keep away from curtains and other combustible materials

• Do not use if there is any damage to the light or cord insulation. Inspect periodically.

PO Box 2228, BELFAST, BT5 9GD

contact@support.ekids.com

LED Light Strip with Remote

Model: iSF-12VM

Computer USB port

polarities match the diagram printed inside.

OFF/ON

Modes

White Light

Light Modes

ENG

Table of Contents

Need help?

Do you have a question about the eKids iSF-12VM and is the answer not in the manual?

Questions and answers

Summary of Contents for KIDdesigns eKids iSF-12VM

Page 1 LED Light Strip with Remote Model: iSF-12VM This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European Directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. For further information, please contact your local or regional authorities.
Page 2 Ruban lumineux LED avec télécommande Modèle: iSF-12VM Ce produit porte le symbole du tri sélectif des déchets d'équipements électriques et électroniques (DEEE).Cela signifie que ce produit doit être traité conformément à la directive européenne 2012/19/EU afin d'être recyclé soit démantelé afin de minimiser son impact sur l'environnement. Pour de plus amples renseignements, merci de contacter les autorités locales ou régionales.Les produits électroniques non inclus dans le processus de tri sélectif sont potentiellement dangereux pour l'environnement et la santé...
Page 3 LED-Lichtband mit Fernbedienung Modell: iSF-12VM Dieses Produkt fällt in die Kategorie „Elektro- und Elektronik-Altgeräte“. Das bedeutet, dass dieses Produkt in Übereinstimmung mit der Richtlinie 2012/19/EU des Europäischen Parlaments und Rates entsorgt oder demontiert werden muss, um schädliche Auswirkungen auf die Umwelt zu minimieren.
Page 4 Striscia LED con telecomando Modello: iSF-12VM Questo prodotto è contrassegnato dal simbolo per la cernita selettiva per i rifiuti di apparecchiature elettriche ed elettroniche (RAEE). Ciò significa che esso deve essere trattato in conformità con la direttiva europea 2012/19/EU , onde riciclarlo o smontarlo riducendo al minimo l'impatto sull'ambiente.
Page 5 Led-lichtstrook met afstandsbediening Model: iSF-12VM Dit product bevat het symbool voor selectief sorteren van afval van elektrische uitrustingen en elektronica (WEEE). Dit betekent dat dit product moet worden gehanteerd overeenkomstig de Europese richtlijn 2012/19/EU ten einde te worden gerecycled of gedemonteerd om de impact op het milieu te minimaliseren. Neem contact op met uw plaatselijke of regionale overheid voor meer informatie.
Page 6 EU Authorised Representative: BMD – 3 Boulevard des Bretonnieres, 49124 St Barthelemy d’Anjou, France The declaration of conformity is issued under the sale responsibility of KIDdesigns, Inc. Object of the declaration: Product Description: USB Powered LED Light (Add Product Image here)
Page 7 Relevant harmonized standards used are listed below: EN IEC 55015:2019+A11:2020 EN 61547:2009 Additional information: The object of declaration is in conformity with the following standards / regulations: For and on behalf of SDI Technologies Inc. Name: David Stetin Title: Product Safety and Compliance Officer Place of issued: Rahway, NJ Date of issued: June 20, 2022...