Advertisement
4.
OPERATION
4.1
Pull out the hoses to the required length. A clicking noise will be heard every half revolution of the drum.
4.2
To latch the reel, allow the reel to slowly retract after hearing the 1st, 2nd or 3rd click.
4.3
To unlatch the reel, slowly pull out the hoses until the clicking noise stops, then let the hoses slowly retract until the hose stopper rests
against the reel mouth.
" WARNING! To prevent injury or damage occurring, do not let go of the hose during rewinding.
5.
MAINTENANCE & STORAGE
" WARNING! Before carrying out routine maintenance or inspection, vent any pressure remaining in the hose.
5.1
The hose reel does not require special maintenance as it is lubricated for life. To ensure reliable operation, clean the hose and
casing regularly. DO NOT spray or wet the product, but clean with a cloth and warm water. DO NOT use solvents or detergents, as
these may permanently damage the plastic.
5.2
Seals
All O-ring seals should be replaced, by an authorised service agent, annually, to ensure reel remains gas tight.
5.3
There are no user serviceable parts. All maintenance and repairs which require the case to be opened or dismantled should be
carried out by an authorised service agent only.
WARNING! DO NOT dismantle the hose reel casing, or attempt to remove the screws and covers on the sides. To do so may result in
"
damage to the appliance and/or personal injury and will invalidate the warranty.
STORAGE
Should you wish to store the air hose, ensure it is clean and dry. Place the item in a dark, safe, dry, childproof location, where the
temperature will remain reasonably stable. DO NOT store in a nylon or plastic bag, as this will encourage condensation.
6.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
Hose will not retract: Hoses bunching within reel.
Spring tension too tight.
Replacement hoses too heavy.
Reel will not latch:
The hoses have been pulled past the latching teeth.
Broken latching pawl or pawl spring.
Reel leaks:
Damaged hoses.
Loose gas connection.
Worn swivel seals.
7.
DECLARATION
Declaration of Conformity We, the sole importer into the UK, declare that the product listed below is in conformity with the following
standards and directives.
OXYACETYLENE HOSE REEL
RGH15.V2
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Welders
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
SOLUTION
Pull hoses out of reel and guide back in.
Have spring tension adjusted by authorised service agent.
Have correct hose fitted by authorised service agent.
Allow reel to retract slowly after hearing 1st, 2nd or 3rd click.
Have new latching pawl or pawl spring fitted by authorised
service agent.
Have new hoses fitted by authorised service agent.
Tighten fitting.
Have new seals fitted by authorised service agent.
The construction file for this product is held by the Manufacturer and may
be inspected, by a national authority, upon request to Jack Sealey Ltd.
Signed by Steve Buckle
01284 757500
01284 703534
1st July 2007
www.sealey.co.uk
Web
sales@sealey.co.uk
email
RGH15.V2 - 1 - 110707
Advertisement
