Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Powermat PM-SWG-600N-3W
- Page 1 USER MANUAL Petrol drilling rig PM-SWG-600N-3W / PM-SWG-600N ORIGINAL MANUAL...
-
Page 2: Table Of Contents
Table of Contents WARNING / INFORMATION SYMBOLS ..................3 APPLICATION OF THE DEVICE ......................... 3 TECHNICAL DATA ..........................4 SAFETY ........................... 4 GENERAL THOUGHTS ............................4 Regarding noise level ........................4 Workplace.......... -
Page 3: Warning / Information Symbols
WARNING / INFORMATION SYMBOLS This graphic sign together with the word WARNING requires special care that should be taken in order not to cause injury. ATTENTION: Before using the device, carefully read the operating manual and safety recommendations. Keep the instructions. ATTENTION: Wear hearing protection and protective glasses while working ATTENTION: Use protective gloves while working ATTENTION: When working, use safety shoes with metal toes... -
Page 4: Technical Data
TECHNICAL DATA Model PM-SWG-600N-3W / PM-SWG-600N 2-stroke Engine type Capacity 52cm 6 hp / 4.41 kW Maximum power 6500 / min Engine revolutions Rotation of the drill up to 150 / min Membrane Carburetor type Engine capacity 1.2 l Fuel used... -
Page 5: Workplace
may exceed the specified value. Please note that exposure to noise can cause hearing loss or loss. WARNING! When operating a drill, it is always recommended to follow basic safety precautions, including the following, in order to reduce the risk of fire, electric shock and injuries. Workplace Keep the workplace well lit and clean. -
Page 6: Using The Tool
body. Keep your balance. Maintain proper posture at all times. This will make it easier to control the tool in case of unexpected working situations. Use protective clothing. Do not wear loose clothing and jewelry. Keep your hair, clothing and work gloves away from moving parts of the tool. - Page 7 While working, avoid contact with earthed, conductive and non-insulated objects such as pipes, radiators and refrigerators. When the drill rig is not in use, it should be stored in a dry, secured place out of the reach of unauthorized persons. When transporting the drill, make sure it is shut down.
-
Page 8: Device Description
DEVICE DESCRIPTION Model: PM-SWG-600N-3W / PM-SWG-600N-3W PRELIMINARY STEPS a) Open the package, then take out the device. b) Remove the protective foil and transport protection (if any). c) Check if the package includes dismantled parts and keys. d) Check that the machine and accessories have not been damaged during transport. -
Page 9: Fuel
Fuel The engine uses 2-stroke fuel, gasoline and 25: 1 2-stroke grease (oil). The 40: 1 mixture is used after the running-in period, this mixture should be used in everyday work with the device. PETROL: Use 95 octane gasoline of good quality. When mixing gasoline with two-stroke engine oil, use only gasoline that is no contains ethanol or methanol (types of alcohols). -
Page 10: Starting The Engine
Make sure all spark plug leads are connected and spark plug is screwed in securely. Check the device carefully from all sides and underneath for fuel leaks. Check that the fuel lines are firmly seated and do not leak. Check that there are no signs of engine damage. -
Page 11: Drilling Holes
STARTING A WARM ENGINE If the fuel tank is not dry, the choke must be in the down position, pull the starter one to three times and the engine should start. WARNING! After the engine is idling, the auger cannot rotate. If the auger starts to rotate after the engine is started, turn the device off (put the main switch in the off position). -
Page 12: Maintenance And Service
5. When drilling is complete, release the throttle only button to put the machine into idle speed. It is impossible to get the engine running at full speed after finishing work. 6. After using the rig for a long time, let the engine idle for a few minutes to cool the engine components. After finishing work, turn the switch to position 0 to turn off MAINTENANCE AND SERVICE Attention. -
Page 13: Carburetor Adjustment
Carburetor adjustment Carburetor adjustment may only be performed by an authorized service technician. If you have a problem with the carburetor, contact your equipment supplier. Incorrect adjustment may damage the engine and void the warranty. Checking the spark plug Do not try to remove the spark plug from the hot engine to avoid possible damage to the thread. Clean or replace the spark plug with heavy oil build-up. -
Page 14: Storage
This is indicated by the symbol on the product, manual or packaging. Thanks to the reuse, use of materials or other forms of using used devices, you make a significant contribution to the protection of our environment. MANUFACTURER'S DATA PH Powermat TMK Bijak Sp. Jawna Ul. Obrońców Poczty Gdańskiej 97 42-400 Zawiercie... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY...
Need help?
Do you have a question about the PM-SWG-600N-3W and is the answer not in the manual?
Questions and answers