Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for PERFECTPASS WakeboardPro
- Page 1 WakeboardPro Graphics Display Mechanical June 2007...
-
Page 2: Table Of Contents
Table of Contents Page No. Section 1 Using WakeboardPro Wakeboard Speed Mode Setting KDW, NN Section 2 Using RPM Mode Section 3 Using Slalom Mode Section 4 Using Name List Section 5 Other Display Features Screen Contrast Quick Reference Guide on Moving Through Menu... -
Page 3: Using Wakeboardpro
Initial System Start Up The very first time your PerfectPass is turned on, it may ask you two questions: 1. [ 5.7L ^ = Yes ] If your boat has a standard 5.7 V8, press the UP key. If you have an optional 6L or 8.1L, press the DOWN key. -
Page 4: Setting Kdw, Nn
To disengage system, pull back on the throttle. The key to good driving is to smoothly drive to engagement speed so PerfectPass can seamlessly take control. If you have a heavily laden boat and need full throttle from start, slowly pull back on handle as speed increases to help PerfectPass engage smoothly. -
Page 5: Using Rpm Mode
Section 2 RPM Mode USING RPM MODE In this mode, the screen will appear as follows: 2. Menu Arrow 1. SETPOINT Speed Base Mode Indicator Speed Tachometer Operating in this mode is very similar to using the Wakeboard or Trick modes, except the system is now controlling to an RPM SETPOINT. -
Page 6: Using Slalom Mode
Section 3 Slalom Mode (Requires Calibration) SIMPLE SLALOM This Simple mode is for recreational skiing and will provide an excellent, tournament quality pull, however, it is not designed to be as accurate as the tournament class Slalom modes. This mode allows you to set speeds in 2 mph increments ranging from 24 – 36 mph. It is designed for those wishing to use the system for open water skiing. -
Page 7: Using Name List
The features available vary depending on the make and model of your boat. If a feature is not present on your PerfectPass then it is not available on your system. To move to the next feature press the MENU key. -
Page 8: Other Display Features
Section 5 Other Features Press Menu & Up keys together to access the following: Screen Contrast – By pressing up or down keys you can change the contrast level. Range is 1 – 5. Lower values = better visibility in extreme sun. 3 is normal. Name List –... -
Page 9: Calibrating Speedometer In Wakeboard Mode
Example: If you are set and engaged at 17 mph, but the analog speedometer or GPS is reading 18 mph, go into the Speedo Cal screen and press the DOWN key several times until the boat speed drops to 17 mph so the PerfectPass Digital Speedometer matches the GPS or boat’s speedometer. -
Page 10: Driving Tips
RPM or Slalom mode is designed for smooth control over 25 mph. “More throttle” If you see the # sign on the screen, this means PerfectPass is running out of control room, press throttle handle slightly ahead until the # disappears. -
Page 11: Troubleshooting
“hunts” above & below Set Speed. Solution: It appears that the PerfectPass throttle cable does not have free movement and is rubbing against engine cover or some other obstacle. A Linkage Test should be performed. See Page 11. - Page 12 Solution: Make sure all 10 pins on Master Module are in-line where display connects. If connection is OK, key pad switch is faulty, return to PerfectPass for repair. Condition: Boat speed drops and throttle handle must be pushed far down to get acceleration.
-
Page 13: System Reset
Servo Motor Test / Auto Tighten Test Every time you return the boat to neutral when PerfectPass is on, the servo will wind in the cable until snug in a clockwise direct. This is the normal starting point for the servo. -
Page 14: Installation
10/32 nut is in place on Morse control / Teleflex throttle cable. Screw threaded brass hex connector on the PerfectPass cable onto the end of the Morse control throttle cable. (Do not over tighten hex nut). Install L shaped brass throttle adapter to throttle control lever using identical hole as original ball joint. - Page 15 Step 3. Mount Dash Display Remove the right speedometer (if boat has two speedometers) or remove tachometer and install the In Dash PerfectPass Display and connect into Master Module. (If there is a speedo tube on back, it should be clamped).
- Page 16 The black wire can be securely connected to any suitable ground. LT-R / LT-1 - On this engine the Gray wire lead on the PerfectPass RPM Sensor cable is not used and can be taped off. The separate Black wire end must be connected to the Gray wire located in the main wiring harness leading into the Borg Warner MDC Control box.
- Page 17 Installation and Set Up of Stern Drive Paddlewheel (Airmar ST300) Tools and Material Required 2 inch hole saw, Sealant eg. GE silicone sealer Installation The 2-inch hole is placed approximately 6-7 inches (16 - 18 cm) perpendicular to the centerline of an inboard ski boat, beside the drain plug under the engine. (See below for v-Drive location).
- Page 18 The PerfectPass Speed Control device should not be used for any other purpose or under any other conditions.
- Page 19 “technical support” as many issues may be easily handled direct with customer. 2. If your PerfectPass was purchased and installed by a dealer you may contact your dealer direct or initiate a warranty claim with PerfectPass.