Summary of Contents for CTS T-2
- Page 1 Operating Instructions and Service Manual T-2 Model Cooling Towers MEMBER 196 Lower Cherry Street Macon, GA 31201 800-752-1905 478-755-1905 800-203-4925 FAX 478-755-8304 FAX www.coolingtowersystems.com info@coolingtowersystems.com...
-
Page 2: Preparations For Starting
The cooling tower blades move large volumes of air quietly and efficiently. CTS incorporates an induced-draft counter-flow design with (a) T-25 – T-230: Made of reinforced plastic material, an axial flow fan mounted on top of the tower to draft air out. -
Page 3: Cautions During Operation
Revolution of the Sprinkler 5-30 40-60 80-250 300-350 400-700 800-3000 12-17 7-10 3.5-5 2.5-4 Sprinkler Head T-2 Model No: 125- 200- 300- 500- 800- 1000 LSU Model No: -040- -050- -065- -080- -100- -125-... - Page 4 10 belts. V-Belt Table (I) V-Belt Speed Belts No. Belts No. Belts No. Fan Speed Belts No. Reducer T-2 Model V-Belt Model of Upper of Lower R.P.M. Total Model No. Pulley Pulley 2-11MS-800 LBM-055C 225 &...
- Page 5 MOTOR AND V-BELT SPEED REDUCER Item No. Description Support Pin Adjusting Lever Adjusting Gauge Adjusting Spring Washer Adjusting Bolt Sight Glass Cooling Fan Lifting Ring Pulley No. 1 V-Belts (Upper) Key A Pulley No. 4 Key D Circlip D V-Belts (Lower) Grease Nipple Housing Cover No.
-
Page 6: Maintenance And Control
(5) MAINTENANCE AND CONTROL 5.3 Tower Casing No coating is needed for the tower casing as it is made 5.1 Sprinkler Pipe of F.R.P. If it becomes soiled, wipe it with soap or a The sprinkler pipe must be clean without blockage. If water-soaked piece of cloth and then wash it there is some foreign material retarded in the pipe, take thoroughly with water. - Page 7 Check the motor temperature polyester tension cords (tensile member). Very and check noise and vibration. compact V-belt drives are possible with this belt. T-2 Model No. 10-15 20-30 40-50 60-80...
-
Page 8: Water Treatment
To replace belts, remove the belt cover from the belt case, slacken the adjusting nut and push the intermediate pulley assembly toward the motor (refer Fig. C). Remove old belts and replace with new sets. (7) PRECAUTIONS IN PROLONGED IDLENESS tower is commissioned, a reguar maintenance program be investigated. - Page 9 Trouble Analysis Table Trouble Causes Counter-Measures Excess or inadequate cooling water flow. Adjust to the specified flow. Irregular flow of air. Improve ventilation. Rise in cooling water Recirculation of air exhausted from tower. Same as above or install baffles. temperature Irregular operation of sprinkler pipes.
- Page 10 Construction & Installation Data www.coolingtowersystems.com - 10 - 40 Years of Manufacturing Experience...
- Page 11 Guarantee COOLING TOWER SYSTEMS, INC. GUARANTEE IS AS FOLLOWS: DOMESTIC – WITHIN THE CONTINENTAL UNITED STATES: Ten Years on FRP, (fiberglass) casing, and cold water basins. Two (2) years on all PVD fillings. One (1) year on all fan motors, major drive components, and all internal moving parts. NOTE: An Extended Manufacturer’s Warranty is available, for an additional nominal fee, and is set into place as part of the original purchase.
Need help?
Do you have a question about the T-2 and is the answer not in the manual?
Questions and answers