Page 1
ZXIMCU P300 Portable Emergency Command System Operation Manual...
Page 3
The copyright of this document belongs to Caltta Technologies Co.,Ltd. Text contains proprietary information owned by Caltta Technologies Co.,Ltd., without the written permission of Caltta Technologies Co.,Ltd., any unit or individual shall not use or leak any document and Figures, this document contains tables, Figure, data and other information.
ZXIMCU P300 Portable Emergency Command System Operation Manual INDEX 1 OVERVIEW..............................1 2 ZXIMCU P300 PRODUCT SPECIFICATION..................2 3 NETWORK ARCHITECTURE INTRODUCTION................3 4 DISPATCHING PC CONFIGURATION....................4 4.1 IP ADDRESS SETTING........................4 4.2 IE 11 BROWSER SETTING......................4 5 TRUNKING SERVICES OPERATIONS....................6 5.1 OPERATIONS OF DAS UNIFIED DISPATCH CONSOLE............ 6 5.1.1 DISPATCH CONSOLE INSTALLATION..............
Page 5
ZXIMCU P300 Portable Emergency Command System Operation Manual 5.2.4 LOCATION........................32 6 CARD ALLOCATION AND NUMBER ALLOCATION..............34 6.1 HAND-HELD TERMINAL NUMBER ALLOCATION.............. 34 6.1.1 LOGIN TO THE UNIFIED OMM................. 34 6.1.2 USER AUTHENTICATION INFORMATION CONFIGURATION......35 6.1.3 USER NUMBER ALLOCATION..................36 6.1.4 ADD GROUP........................39...
Page 6
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure Index Figure 1-1 ZXIMCU P300 with battery ....................1 Figure 1-2 ZXIMCU P300 without battery....................2 Figure 2- 1 ZXIMCU P300 Operation Panel Diagram................2 Figure 3- 1 System Network Architecture....................3 Figure 4- 1 Adding Route...........................4...
Page 7
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 26 Map interface display and operation................22 Figure 5- 27 Frame select on the map....................22 Figure 5- 28 Frame select and dispatch on the map................23 Figure 5- 29 Dispatch console initiates a video pull................24 Figure 5- 30 Toolbar of the video display window................25...
Page 8
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 6- 19 Setting dispatcher account information................48 Figure 7- 1 Trusted sits setting of the Internet Options..............49 Figure 7- 2 Security settings of trusted sites-1..................50 Figure 7- 3 Security settings of trusted sites-2..................51 Figure 7- 4 Security settings of trusted sites-3..................
ZXIMCU P300 Portable Emergency Command System Operation Manual Overview ZXIMCU P300 Manpack Emergency Command System highly integrates base-band unit, radio unit, core network and multimedia dispatch, quickly implements the on-site deployment of LTE emergency network, provides rich LTE-based services such as professional trunking call, multimedia dispatch, real-time video transmission, GIS location, audio/video full duplex call, etc., which is widely adopted in emergency...
Interface display screen Network Architecture Introduction Caltta LTE portable emergency command system is based on All-IP flat network architecture. The system follows B-TrunC Broadband Trunking standard, integrates LTE core network iEPC, professional voice and video trunking network DSS, multimedia dispatching server MDS, base station system and terminals, and provides end-to-end multimedia command and dispatch solution.
ZXIMCU P300 Portable Emergency Command System Operation Manual Multimedia dispatching server MDS has various functions such as mobile video surveillance, Video pull, video distribution, video dubbing, etc. Dispatching PC Configuration Both common PC or laptop can be used as dispatching PC. The PC operating system requires Win 7 or above.
Page 13
ZXIMCU P300 Portable Emergency Command System Operation Manual Before logging in, make sure the PC has been installed with Adobe flash player and the IE settings are correct, otherwise the OMM interface may not open. The Adobe flash player plug-in and IE setting script can be downloaded and installed on the OMM interface.
ZXIMCU P300 Portable Emergency Command System Operation Manual Press Enter button after inputting the IP address, the script will set up automatically. Click any key to exit when finishing set up. Trunking Services Operations Operations of DAS Unified Dispatch Console 5.1.1...
ZXIMCU P300 Portable Emergency Command System Operation Manual Input the account number and password on the login interface of dispatch console , select Remember Password and click the setting icon on the right side, Input the server IP address (IP address of the trunking dispatch console) and MDS IP address, then click Login to login in the dispatch console.
Page 17
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 4 Dispatch console interface 5.1.3.1 Dispatch Console Interface Layout Figure 5- 5 Dispatch console interface layout The dispatch console interface is divided into four areas as shown above, introduction of each (marked with number) is as follows: Area 1: Menu area, with five icons of Dispatch, GIS, Video, History and Setting, ...
Page 18
ZXIMCU P300 Portable Emergency Command System Operation Manual Area 2: User list area, which shows the authorized users of the system and user online status. The hand-held terminal means default fleet user, individual device means camera user. Click the icon on the upper right corner of user list to display or hide the user list.
Page 19
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 7 Remove user from dispatching operation area Sound channel selection: When the dispatch console dispatches users, groups or dispatchers, it supports switching between balance channel model and exclusive main channel model.
Page 20
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 9 User call attribute setting Group call attribute setting: Move cursor to a group, right click and select Call attribute from the shortcut menu to select a call attribute as required.
Page 21
ZXIMCU P300 Portable Emergency Command System Operation Manual 5.1.3.3 General Operations of GIS Dispatch Select GIS from the menu, display the map interface. Figure 5- 12 GIS interface of the dispatch console The dispatch console supports both online and offline maps. Make sure the dispatching PC has been connected to the map server before logging to the dispatch console.
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 13 Video dispatch interface 5.1.4 Dispatch Console Initiates a Half-duplex Voice Private Call Move cursor to the user on the trunking dispatch interface, right click and select Call attribute from the shortcut menu and and uncheck the "Full duplex" option;.
ZXIMCU P300 Portable Emergency Command System Operation Manual 5.1.5 Dispatch Console Initiates a Full-duplex Voice Private Call Move cursor to the user (Call attribute defaults to Full duplex) and click the Call origination icon in the middle, then the dispatch console and corresponding terminal will ring.
ZXIMCU P300 Portable Emergency Command System Operation Manual 5.1.7 Dispatch Console Initiates a Voice Group Call Move cursor to a group and click Initiate Call in the middle, the terminals in the group will automatically answer the call and establish a voice group call. By default, the dispatch console has the floor.
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 18 Dispatch console initiates a video group call 5.1.9 Sending SMS and MMS Move cursor to an online user in the user list, right click and select Send Message from the shortcut menu to send SMS and MMS to the terminal. Multiple file formats are supported (up to 20 MB).
ZXIMCU P300 Portable Emergency Command System Operation Manual Select the ongoing call, and click to forcibly release the call. Figure 5- 20 Forced release by the dispatcher Forced Insertion Forced insertion is only applicable to group call. When a terminal initiates a group call...
ZXIMCU P300 Portable Emergency Command System Operation Manual To remove a dynamic member, click under the corresponding member. Figure 5- 22 Dynamic regroup 5.1.12 Temporary Group Call Different from dynamic regroup, temporary group call is to temporarily create a group.
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 23 Temporary group call 5.1.13 Emergency call In case of emergency, you can press the SOS emergency call button on the terminal to send an emergency call to the dispatch console and other terminals in the group.
Page 29
ZXIMCU P300 Portable Emergency Command System Operation Manual Click Location to locate the terminal user. When the terminal has displayed the positioning status, click Cancel Location to end the positioning. Figure 5- 25 Dispatch console location operation The location is successful if the terminal information is shown on the map. Move cursor to a terminal on the map, the detailed location information will be displayed in the following red box 1 .
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 26 Map interface display and operation 5.1.15 Frame Select and Dispatch on the Map Frame select terminals on the map to make a temporary group call. Figure 5- 27 Frame select on the map Tick the terminals in the pop-up box that need to be called, and click Call to start the group call.
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 28 Frame select and dispatch on the map 5.1.16 Dispatch Console Initiates Video Pull. Select Dispatch on the system menu, and then switch to the Video Dispatch interface. Move cursor to a user, the user will be highlighted. Right click the user to display the operation menu.
Page 32
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 29 Dispatch console initiates a video pull Adjust the number of terminal videos to be displayed on the upper area of the Video interface. Click to customize the display mode.
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 30 Toolbar of the video display window 5.1.17 Dispatch Console Initiates Video Distribution Pull a terminal video to the dispatch console first, and then move cursor to the video display window, the toolbar will be shown. Click at the video’s bottom right...
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 31 Dispatch console Initiates video distribution Operations of Multimedia Dispatch System The Multimedia Dispatch System (MDS) client supports independent client operations. It’s required to install the client before logging. Install the CS dispatch console client on the dispatching PC. Click the installation file, then click Next until the installation is completed, as shown in the following figure.
ZXIMCU P300 Portable Emergency Command System Operation Manual 5.2.1 Dispatcher Login Open the CS dispatch console client. If the the PC has multiple IP addresses, the client will prompt you to select the IP address. Select the correct IP address of PC that accesses with the client, and then turn to the login interface.
Page 36
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 34 Operations of the multimedia dispatch video pull After the video is pulled, the video captured by the user's camera can be viewed on the dispatch console. See the following figure: Click at the lower right corner of the video window to end the video pull.
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 35 Multimedia dispatch video display window 5.2.3 Video Distribution Dispatch console can distribute the pulled videos to terminals and groups. Select a video that has been pulled on the interface of the dispatch console, click on the lower right corner of the window, then the distribution page will pop up.
Page 38
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 36 Multimedia dispatch video distribution Click Start Distribution to distribute the video. For example, after a video is successfully distributed to user 5903, the pull and distribution status will be displayed on both the user list and the distribution list.
Page 39
ZXIMCU P300 Portable Emergency Command System Operation Manual After the video is successfully distributed, the screen of terminal will display the video source, as shown below: Figure 5- 38 Video is distributed to the receiving terminal. Click End on the Terminal who is receiving video to end the video distribution.
ZXIMCU P300 Portable Emergency Command System Operation Manual 5.2.4 Location Terminals and groups can be located at the Map interface of the dispatch console. Select the terminal to be located, and select Location from the shortcut menu, see the following figure.
Page 41
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 5- 41 MDS location display Right click the contact list of the terminal and select to view the historical track replay of the terminal, as the following figure. Figure 5- 42 Viewing historical track of the terminal Input the Start time and End time on the Historical Track page, and click Search to query the historical track of the terminal.
ZXIMCU P300 Portable Emergency Command System Operation Manual Click to pull the video, see the following figure. Figure 5- 43 Dispatching the terminal on the Map interface Card Allocation and Number Allocation Hand-held Terminal Number Allocation 6.1.1 Login to the unified OMM Login to the unified OMM via IE browser (IE 11).
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 6- 1 Unified OMM interface 6.1.2 User Authentication Information Configuration , select Authentication, and switch to the Step1: Click Operation Management Authentication information interface. Select Add card under the menu to add the...
ZXIMCU P300 Portable Emergency Command System Operation Manual Step 2: Input the IMSI number and SIM card authentication information (User key, Authentication management domain and OPC, can directly copy the existing card information) on the Add card page. Click Save to complete operation, as the...
Page 45
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 6- 4 Add user Step 2: On the pop-up Add user page, input the IMSI number, User number (beginning with 1880755), tick Activated data service, select iepc.com as the data service template, tick Subscribed PTT service, input Fleet user number...
ZXIMCU P300 Portable Emergency Command System Operation Manual 6.1.4 Add Group Step1: Click Operation Management ->Group and switch to the Group management interface, and select ZiLTE group under menu on the right to add group: Figure 6- 7 Add group Step 2: Input Group number (beginning with 6880755), Group short number, and Group name on the Add group interface.
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 6- 8 Group account information setting Note: Select the group to be operated, click to edit or delete the group. 6.1.5 Add group member Select the group that need to add group members, and click the number in the Group member column, see the following figure.
Page 49
ZXIMCU P300 Portable Emergency Command System Operation Manual Click on the right of the group member page to display the page for editing group members, see the following figure. Figure 6- 10 Add group member-2 Select the member to be added from the available members list, and click to add the group member, see the following figure.
ZXIMCU P300 Portable Emergency Command System Operation Manual Select the group member to be edited, and click to display the page for editing group member attributes. Modify the information, and click Save. The group member attribute will be modified. Figure 6- 12 Modify the group member attribute CPE Terminal Number Allocation 6.2.1...
ZXIMCU P300 Portable Emergency Command System Operation Manual 6.2.3 User Number Allocation Step 1: Click Operation Management -> User and switch to the user management interface, select ZiLTE under menu on the right to add user. This step is the same as that of hand-held terminal number allocation.
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 6- 14 Enter to expert diagnosis mode on the unified OMM interface. 6.2.5 APN Configuration The APN configuration mainly include CPE Access Terminal IP Pool Configuration and CPE Terminal Authorization Profile Configuration.
Page 53
ZXIMCU P300 Portable Emergency Command System Operation Manual IP Segment Start:45.45.x.1 IP Segment End: 45.45.x.254 Mask: 255.255.0.0 x represents any number of 0-254. The x of the IP Segment Start is the same as the IP Segment End. Figure 6- 15 Add CPE IP Pool and IP Segment.
ZXIMCU P300 Portable Emergency Command System Operation Manual CPE IP: The IP address used by the CPE to obtain wireless signal, which is the corresponding IP address inside the IP pool (recommend: 45.45.x.2, where x is the IP network segment of the corresponding address pool).
ZXIMCU P300 Portable Emergency Command System Operation Manual Figure 6- 17 Show CPE access status Dispatcher Management Step1: Select Operation Management -> Dispatcher, switch to the dispatcher management interface. Click on the right side to show interface of adding a dispatcher.
Page 56
ZXIMCU P300 Portable Emergency Command System Operation Manual Step2: Input the corresponding information according to the interface requirements (the dispatcher number beginning with 8880755, 11 digits), and click Save at the bottom to complete the operation of adding a dispatcher, see the following figure:...
ZXIMCU P300 Portable Emergency Command System Operation Manual References Manually Add Trusted Sites to the IE Browser IE 11 (win 7 32-bit operating system) is used for the login and related operations of the dispatch console and OMM of the ZiLTE system. It’s required to configure the IE...
Page 58
ZXIMCU P300 Portable Emergency Command System Operation Manual Return to the page of Internet Options [Security], select Trusted sites and click Custom level to enter the Security Settings - Trusted Sites Zone page to set the security level of the trusted sites. Set all the sub-items under ActiveX controls and plug-ins to Enable, see the following figures.
Page 60
ZXIMCU P300 Portable Emergency Command System Operation Manual Return to the page of Internet Options [General], and click Settings to enter the Temporary Internet Files page. Select [Every time I visit the webpage] -> [OK], see the following figure. Figure 7- 5 Temporary Internet Files Settings Switch to the page of Internet Options [Privacy], and remove the check mark of "Turn on Pop-up Blocker"...