Table of Contents
Advertisement
Quick Links
USER MANUAL FOR SUBSEA DIAMOND WIRE SAW 0-320mm
Document title
IKM TECHNOLOGY AS ref.
Customer ref.
Rev.
Date
01
13.05.2014
02
16.06.2016
03
03.09.2020
:
UMA-7644-001/005 Subsea Diamond Wire Saw
:
P7644
:
Subsea Tool
Reason For Issue
Issued for use
Update
Re-issued for Use
Prepared Checked Approved
JHR
KOS
KF
EN
OG
TSH
EN
KG
OG
Advertisement
Table of Contents
Related Manuals for IKM P7644
Summary of Contents for IKM P7644
-
Page 1: User Manual For Subsea Diamond Wire Saw 0-320Mm
USER MANUAL FOR SUBSEA DIAMOND WIRE SAW 0-320mm Document title UMA-7644-001/005 Subsea Diamond Wire Saw IKM TECHNOLOGY AS ref. P7644 Customer ref. Subsea Tool Rev. Date Reason For Issue Prepared Checked Approved 13.05.2014 Issued for use 16.06.2016 Update 03.09.2020 Re-issued for Use... -
Page 2: Table Of Contents
Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS USER MANUAL FOR SUBSEA DIAMOND WIRE SAW 0-320MM ......... 1 GENERAL INFORMATION ................3 Abbreviations ....................4 References ....................5 TECHNICAL SPECIFICATION ..............6 SAFETY ....................... 7 General - Operations .................. -
Page 3: General Information
Company: IKM Technique AS GENERAL INFORMATION This manual is a user manual for the IKM Technology 190mm and 320mm Diamond Wire Saw (DWS). The DWS system consists of a hydraulic motor, drive system, chassis and a Diamond wire. The DWS is designed to be handled by an ROV, with typical a Schilling 7 function manipulator. -
Page 4: Abbreviations
2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS Abbreviations British standard pipe Cubic centimetre Counter clockwise Diamond Wire Saw Hydraulic Power Unit Joint Industry Council Kilo gram Litre per minute... -
Page 5: References
2014.12.29 Approved date: 2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS References Doc no. Description Rev. Issued Can be found 7644-001 Drawing Subsea Diamond Wire Saw 190mm 06.11.15 Appendix A... -
Page 6: Technical Specification
The feed is controlled in small steps by the operator to apply a firm push/engagement of the running wire against the cut object. IKM-1044812 is the clamp for DWS 7644-001 (Ø185) IKM-1044551 is the clamp for DWS 7644-005 (Ø320) -
Page 7: Safety
IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS SAFETY General - Operations Only authorised people and qualified personnel should work on the system, and take suitable precautions to prevent any potential injuries. Always adhere to authorised working practices, and use the correct tools for the job. -
Page 8: Special Note To The Dws
Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS Always ensure that items are correctly and adequately supported before removal, and that authorised lifting equipment and procedures are used. Note: trying to lift heavy components in an awkward position by hand without the assistance of correct lifting equipment, or lifting any component without adopting the correct stance, can lead to serious injury. -
Page 9: Operational Description
Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS OPERATIONAL DESCRIPTION The following description is a generic description of preparation and use of the DWS. Customers are advised to adapt the following information to their own specific operations and specific work area. -
Page 10: Step By Step Procedure
Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS Step by Step Procedure General Perform SJA/Toolbox talk for the operation as required by client/ROV contractor’s own procedures. Operation The following steps are to be regarded as guidelines for operation. Operator of the tooling must adapt the steps into their own operations procedure. -
Page 11: Maintenance
IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS MAINTENANCE Maintenance of the DWS is limited to flushing with fresh water and oil after use for corrosion protection. However, if multiple cuts are performed and wires are to be replaced;... - Page 12 BTE.12-26 User Manual Page 12 of 21 Dok.ID: 010984 Issue date: 2014.12.29 Approved date: 2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS...
-
Page 13: Spare Part List
Issue date: 2014.12.29 Approved date: 2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS SPARE PART LIST ➢ Diamond wire ➢ Hydraulic hoses and connections ➢ Nuts and bolts ➢ Motor... -
Page 14: Revision Changes
2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS REVISION CHANGES Revision Procedure change Author Original version Update Update including Feed Clamp CONTACT INFORMATION All enquiries relating to the tooling should be addressed to:... -
Page 15: Appendix
Approved date: 2015.02.13 Rev.no: Author: Gabrielsen Trine (Technique) Owner: IKM Administrator Approved by: Reinsnos Jostein (Technique) Company: IKM Technique AS APPENDIX Doc number Description Appendix A 7644-001 Drawings of DWS 185mm Appendix B 7644-005 Drawings of DWS 320mm Appendix C... - Page 16 Appendix A...
- Page 17 Appendix A...
- Page 18 Appendix A...
- Page 19 Appendix A...
- Page 20 Appendix A...
- Page 21 Appendix A...
Need help?
Do you have a question about the P7644 and is the answer not in the manual?
Questions and answers