Table of Contents
Advertisement
Quick Links
Venetian blind motor:
GEIGER GJ56.. E14 Perfection with electronic end stop
For Venetian blinds and exterior blinds
Original-Montage- und
DE
Betriebsanleitung
Original assembly and
EN
operating instructions
Notice originale de montage
FR
et d'utilisation
Instrucciones originales de
ES
instalación y funcionamiento
Istruzioni originali di installazione
IT
e funzionamento
www.geiger.de
EN
1
EN
Advertisement
Table of Contents
Summary of Contents for GEIGER GJ56 E14 Series
- Page 1 Venetian blind motor: GEIGER GJ56.. E14 Perfection with electronic end stop For Venetian blinds and exterior blinds Original-Montage- und Betriebsanleitung Original assembly and operating instructions Notice originale de montage et d’utilisation Instrucciones originales de instalación y funcionamiento Istruzioni originali di installazione e funzionamento www.geiger.de...
-
Page 2: Table Of Contents
1. General information Dear customer, By purchasing a GEIGER motor you have decided on a quality product from GEIGER. Thank you very much for your decision and the confidence placed in us. Before you put this drive into operation please observe the following safety instructions. It serves for the prevention of danger and for the avoidance of personal injury and damage to property. -
Page 3: Intended Use
GJ 56 Design options Torque in Nm For head rails at least 56 mm GEIGER Venetian blinds motor 4. Safety instructions ATTENTION: Important safety instructions. For personal safety, it is important to follow these instructions. Please keep these instructions for future reference. -
Page 4: Assembly Note
A plug for the disconnection of the motor from the power supply must be accessible after installation. f Damaged connecting cables must be replaced by GEIGER connecting cables of the same type. f The device must be mounted as described in the installation instructions. Fixations shall not be made with adhesives since they are regarded as unreliable. -
Page 5: Installation Instructions
7. Installation instructions Prior to installation please check to ensure there is no visible damage to the motor like cracks or open cables. Before fixing please check the strength of the masonry and of the surface. Head rail opening at top: www.geiger.de... - Page 6 Head rail opening at bottom: Gerhard Geiger GmbH & Co. KG | 100W2589 V000 0323...
-
Page 7: Information For The Specialist Electrician
UP/DOWN keys must be activated simultaneously instead of the programming key. The motor can also be operated with the limit stop switch and a standard switch. Article number / GEIGER setting switch M56F154 with service terminal (D), 4-wires... -
Page 8: Calling Up The Different Modes
DOWN key on the blind switch. The motor moves for 1 second. Press key Keep both keys pressed for another 3 seconds. The motor confirms with a short movement downwards. Gerhard Geiger GmbH & Co. KG | 100W2589 V000 0323... -
Page 9: Programming/Changing The End Stops
The lower end position is unchanged and the programming is completed. • The motor is now always turned off by the limit stop switch/switches off (torque shut-off) at top. www.geiger.de... -
Page 10: Correction Of The End Positions Or The Shade Position
If this is the case, the upper end position is readjusted. The motor stops on the limit stop switch/at top by the reference runs. Gerhard Geiger GmbH & Co. KG | 100W2589 V000 0323... -
Page 11: Resetting To Factory Setting
• The motor was installed upside down or the actuates the limit stop switch and can lower end position has been overrun and no longer be moved downwards. the lift tapes were wound up incorrectly. Allow free mobility of the limit stop switch. Reset the end stops. www.geiger.de... -
Page 12: Declaration Of Conformity
Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen Phone +49 (0) 7142 9380 | Fax +49 (0) 7142 938 230 | info@geiger.de | www.geiger.de Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146 Komplementär: Geiger Verwaltungs-GmbH | Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRB 300481 Geschäftsführer: Roland Kraus | WEEE-Reg.-Nr. -
Page 13: Technical Data
Storage temperature T = -15°C .. +70°C Run-time optimized version Subject to technical modifications. Please find information to the ambient temperature range of our GEIGER motors under www.geiger.de 22. Maintenance The drive is maintenance-free. 23. Notes on waste disposal Recycling of packaging materials In the interest of environmental protection, please contact your local government’s recycling or... - Page 14 Gerhard Geiger GmbH & Co. KG | 100W2589 V000 0323...
- Page 15 www.geiger.de...
- Page 16 Gerhard Geiger GmbH & Co. KG | 100W2589 V000 0323...
Need help?
Do you have a question about the GJ56 E14 Series and is the answer not in the manual?
Questions and answers