Advertisement
Quick Links
69-20250 Ford Super Duty Tremor SST Kit
IF your ReadyLIFT
product has a damaged or missing
®
part, please contact customer service directly and
a new replacement part will be sent to you immediately.
For warranty issues, please return to the place of
installation and contact ReadyLIFT.
(877) 759-9991
MON-FRI 7AM-4PM PST
OR
EMAIL: support@readylift-ami.COM
WEBSITE: ReadyLIFT.COM
**Please retain this document in your vehicle at all times.**
Limited Lifetime Warranty
This unique product warranty proves our commitment to the quality and reliability of every product that
ReadyLIFT manufactures. The ReadyLIFT product warranty only extends to the original purchaser of any
ReadyLIFT product, if it breaks, we will give you a new part. Warranty does not apply to discontinued parts.
Our Limited Lifetime Warranty excludes the following ReadyLIFT items; bushings, bump stops, ball joints, tie
rod ends, heim joints and shock absorbers. These parts are subject to wear and are not considered defective
when worn. They are warranted for 12 months from the date of purchase for defects in workmanship.
This product warranty is voided if the vehicle is not aligned after kit installation and proper maintenance is
routinely done.
Product purchased directly from ReadyLIFT has a 90 day return policy on uninstalled products from the date
of purchase (may be subject to restocking fee). Uninstalled product returns must be in the original
ReadyLIFT packaging. Please call (877) 759-9991 to get an RGA# for any return. Customer is responsible
for shipping costs back to ReadyLIFT. Returns without RGA# will be refused. Contact ReadyLIFT
directly about any potentially defective parts prior to removal from vehicle.
ReadyLIFT products are NOT intended for off-road abuse. Any damage or failure as a result from off-road
abuse voids the warranty of the ReadyLIFT product. ReadyLIFT is NOT responsible for any subsequent
damages to any related vehicle parts due to misuse, abuse, improper installation, or lack of maintenance.
Furthermore, ReadyLIFT reserves the right to change, modify or cancel this warranty without prior notice.
www.ReadyLIFT.com - Phone: (877) 759-9991
69-20250-IM-AA
Advertisement
Related Manuals for ReadyLift 69-20250
Summary of Contents for ReadyLift 69-20250
- Page 1 ReadyLIFT manufactures. The ReadyLIFT product warranty only extends to the original purchaser of any ReadyLIFT product, if it breaks, we will give you a new part. Warranty does not apply to discontinued parts. Our Limited Lifetime Warranty excludes the following ReadyLIFT items; bushings, bump stops, ball joints, tie rod ends, heim joints and shock absorbers.
- Page 2 Failure to drive safely may result in serious injury or death to driver and passengers. Driver and passengers must ALWAYS wear your seat belts, avoid quick sharp turns and other sudden maneuvers. ReadyLIFT Suspension does not recommend the combined use of suspension lifts, body lifts, or other lifting devices.
-
Page 3: Important Note
Always measure the vehicle ride height prior to beginning installation. A lifted vehicle may have different headlight aim performance. ReadyLIFT recommends marking and recording the headlight beam position before kit installation and then adjusting, if necessary, the headlamps to the same height settings after kit installation. - Page 4 PRE-INSTALLATION MEASUREMENTS: It is imperative that you record the following measurements and factory components in the tables below. ReadyLIFT tests and records as much data from each application as available at the time of product development. Vehicle manufacturers may change components or add models with different options.
-
Page 5: Bill Of Materials
Professional knowledge and skill will typically yield the best installation results. If you need an installer in your area, please contact ReadyLIFT Suspension Customer Service or check out the dealers tab on our Website for authorized installers . - Page 6 ReadyLIFT recommends all steps and procedures described in these instructions be performed while the vehicle is properly supported on a two post vehicle lift with safety jacks. Otherwise, park vehicle on a clean flat surface and block the rear wheels for safety.
- Page 7 Rotate the axle until you can line up the radius arms into the ReadyLIFT drop brackets. Install using factory hardware. Do not tighten at this time. Remove the brake line bracket at the frame. Remove the brake line bracket at the axle.
- Page 8 Remove the track bar from the factory bracket. Remove the factory track bar bracket from the frame. Install the ReadyLIFT track bar bracket to the frame using factory hardware. Torque ft-lbs. Install the track bar to the ReadyLIFT bracket using factory hardware.
- Page 9 Install the ReadyLIFT shock extensions to the axle using factory hardware. Install the shock to the ReadyLIFT shock extensions using the M14 x 70mm bolt, washers and nuts. Torque to ft-lbs. Reattach the factory brake line bracket at the axle using factory hardware.
- Page 10 Remove the driver side u-bolts completely and discard. Lower the axle just enough to remove the factory block and install the ReadyLIFT block, making sure not to over extend brake and ABS lines. Adjust as necessary. www.ReadyLIFT.com - Phone: (877) 759-9991...
- Page 11 Repeat steps for passenger side. If equipped with a 2 piece driveline, remove the bolts holding the carrier bearing to the frame. Install the ReadyLIFT carrier bearing spacer between the carrier bearing and frame using 7/16” bolts, washers and nuts.
- Page 12 Caster Bushings if it is not possible to get caster within recommended specs. RECOMMENDED ALIGNMENT SPECS Front Driver Passenger Tolerance Total / Split Camber -0.3 +0.3 +/- 0.5 +0.0 Caster +2.5 +2.5 +/- 0.5 +0.0 +.05 +.05 +/-0.05 +.20 www.ReadyLIFT.com - Phone: (877) 759-9991 69-20250-IM-AA...
Need help?
Do you have a question about the 69-20250 and is the answer not in the manual?
Questions and answers