Page 3
2- INSTALLATION ON HORIZONTAL OR VERTICAL PIPE 3- OPERATION CYCLE OF BLIDING WITH ONIS LINEBLIND 4- RANGE OF USE – ADDITIONAL PRECAUTIONS ONIS - 1, avenue F.Julien - Z.I. de Bertoire - 13410 LAMBESC France Page onis@onis.fr Tel : (33) 4 42 92 93 20 Fax : (33) 4 42 92 73 52 - E-mail...
Page 4
ONIS Lineblind + 2 times the thickness of a flange's gasket. + or – 3mm MAXI Keep flexibility for one of the two pipes to permit to clamp and spread the seats of the ONIS with an useless effort.
Page 5
DATE : 25/07/05 Additional Check point when lineblind is on line Reinforcement must not be in contact with the stud bolts ONIS - 1, avenue F.Julien - Z.I. de Bertoire - 13410 LAMBESC France Page onis@onis.fr Tel : (33) 4 42 92 93 20 Fax : (33) 4 42 92 73 52 - E-mail...
Page 8
Decompress between the valves and the ONIS lineblind Clean the visible part of the spectacle plate ONIS - 1, avenue F.Julien - Z.I. de Bertoire - 13410 LAMBESC France Page onis@onis.fr Tel : (33) 4 42 92 93 20 Fax : (33) 4 42 92 73 52 - E-mail...
Page 9
4 – RANGE OF USE – ADDITIONNAL PRECAUTIONS Design conditions The ONIS lineblind, which you have just acquired, was designed according to the information you have transmitted to us on the technical specification SOCOMET F03 when you have passed the order.
Page 10
In that case the leak could feed the fire. Additional safety devices Except if it is originally provided with it, the ONIS lineblind can be equipped with accessories which can improve the reliability and safety of use as: o Protection covers to limit the degradation of gaskets by chock or external...
Page 11
4- Setting of the lineblind 5- Instruction and Maintenance documents for additional devices (gear box, actuators, limit switches…) ONIS - 1, avenue F.Julien - Z.I. de Bertoire - 13410 LAMBESC France Page onis@onis.fr Tel : (33) 4 42 92 93 20 Fax : (33) 4 42 92 73 52 - E-mail...
Page 12
There is no stainless steel inserts. Slide gate To ensure perfect sealing, check seal condition before any operation. ONIS - 1, avenue F.Julien - Z.I. de Bertoire - 13410 LAMBESC France Page onis@onis.fr Tel : (33) 4 42 92 93 20 Fax : (33) 4 42 92 73 52 - E-mail...
Page 13
In aggressive environment, cover the shafts with grease to avoid corrosion. It is only required, once a year, to pour liquid oil on the shaft at the ring level and to operate the ONIS lineblind to allow dispersion. Use of greasing spray is recommended.
Gear Box : On critical application, it is recommended to have 1 gearbox in your stock. ONIS - 1, avenue F.Julien - Z.I. de Bertoire - 13410 LAMBESC France Page onis@onis.fr Tel : (33) 4 42 92 93 20 Fax : (33) 4 42 92 73 52 - E-mail...
Page 15
Receipt shafts Motor or excentric shafts ONIS - 1, avenue F.Julien - Z.I. de Bertoire - 13410 LAMBESC France Page onis@onis.fr Tel : (33) 4 42 92 93 20 Fax : (33) 4 42 92 73 52 - E-mail...
Page 17
(pure or carbonated water) and followed by compressed air drying. Before any operation with the ONIS lineblind, clean the sliding gate and the external seals. It is only after the piping cleaning and the complete drainage of cleaning fluid that the ONIS lineblind can be operated.
Page 18
DOCUMENT : F36 Rev F ONIS LINEBLIND DATE : 25/07/05 ONIS thank you for choosing ONIS lineblind to blind your pipe. Our representative agents and ONIS stay at your full disposal for any question you may have. Do not hesitate to contact us. ONIS Z.I.