RC Logger X3 Mini Gimbal PRO Operating Instructions

Operating instructions
X3 Mini Gimbal PRO
No. 10010RC
INTENDED USE
Please download the latest version of the operating instructions
from our website at www.rclogger.com. Navigate to the product
page and open the "Downloads" tab. Click on "Operating
instructions" to start the download.
Make this product available to third parties only together with
its operating instructions.
The X3 Mini Gimbal attaches to the NovaX 350 quadcopter and can hold GoPro
as GoPro HERO4 Black/Silver, GoPro HERO3+, GoPro
® ®
is supplied with power by the NovaX 350 flight battery and controlled via transmitter/receiver.
Through the installed video transmitter you can transmit live video to a video receiving device.
It is solely intented for private use in the model making area and not to be used for commercial
applications. The product must not become damp or wet.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. If you
pass the product on to another person, pass along the operating instructions as well. Read the
instructions carefully and keep them.
DELIVERY CONTENT
> Gimbal
> Antenna
> 3-pin cable
> USB cable
> Video cable for GoPro
camera (pre-installed on gimbal)
®
> Video cable for Yi camera
> SMA extension
> 90° SMA adapter
> Brown/Black and white spare cables
> USB adapter
> 12x Rubber dampers (6 x red, 6 x black)
> Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially
observe the safety information. If you do not follow the safety
instructions and information on proper handling in this manual,
we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/
guarantee.
Consult the »NovaX 350 manual for instructions on how to
attach, connect and operate accessories. Mind the max. takeoff
weight.
> The device is not a toy. Keep it out of the reach of children and pets.
> Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
> Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
> Do not use the product in rain.
> Do not place the product under any mechanical stress.
> If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
» is visibly damaged,
» is no longer working properly,
» has been stored for extended periods in poor ambient conditions or
» has been subjected to any serious transport-related stresses.
> Please handle the product carefully. Jolts, impacts or a fall even from a low height can
damage the product.
> Also observe the safety and operating instructions of any other devices which are connected
to the product.
cameras such
®
HERO3, and Yi camera. The gimbal
®
INSTALLATION
Compatibility:
Note that the supplied gimbal is only installable on NovaX 350
models that feature the quick release gimbal platform. Refer to
the latest NovaX 350 operating instructions for more information.
1. Study the installation photos (step 1 – step 5) on the next page.
2. If you have an existing platform installed, remove it.
3. Place the slot holes in the platform over the studs. Then, slide the platform to the side, so
that the studs enter the slots. Now, lock the platform with the lock lever (step 1). You must
ensure that the lock lever is securely locked in the stud as otherwise the platform may come
off during flight!
» It may be necessary to move the installed receiver further towards the edge of the
NovaX 350's bottom to make space for the gimbal connections.
4. Remove the bracket that secures the camera in the camera tray by removing the screws.
Turn the gimbal arm so that the pitch motor (the one that controls the rotation of the camera
tray) stands on the left side when you look at the camera tray.
If the pitch motor is not located on the left the gimbal will be
damaged when you supply power.
You must install a camera and the antenna before you supply
power to the gimbal or it will be damaged.
5. Install a camera into the camera tray and secure it with the bracket and screws. Connect
the video cable to the camera's video port. The video cable for GoPro
installed on the gimbal. If you use a Yi camera use the video cable for Yi cameras instead.
(step 2)
6. Install the antenna on the antenna port. Use the 90° SMA adapter or the SMA extension
cable if needed. (step 3)
7. Remove the canopy of the NovaX 350 and locate the GIMBAL_X header on the PCB board.
8. Connect the 3-pin cable to the GIMBAL_X header (step 4). Mind the direction as indicated
on the board! Connect the other end to the port on the video transmitter. (step 5)
9. Install the canopy again.
10. Connect the Blue/Yellow/Black cable to the corresponding connector on the rear of the
gimbal on the gimbal board if it is not already connected.
11. Secure loose cables with cable ties if needed.
12. The installation is complete.
WIRING DIAGRAM
Receiver
Heading Pitch Mode Video
cameras is already
®
5V
Video Output Cable
Video
Control
Video
GND
Flight battery