Renesas DALI Master Controller GUI User Manual
  1. Manuals
  2. Brands
  3. Renesas Manuals
  4. Lighting Equipment
  5. DALI Master Controller GUI
  6. User manual
Renesas DALI Master Controller GUI User Manual

Renesas DALI Master Controller GUI User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DALI Master Controller GUI
All information contained in these materials, including products and product specifications,
represents information on the product at the time of publication and is subject to change by
Renesas Electronics Corp. without notice. Please review the latest information published by
Renesas Electronics Corp. through various means, including the Renesas Electronics Corp.
website (http://www.renesas.com).
Rev.4.00 Nov. 2022
www.renesas.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DALI Master Controller GUI and is the answer not in the manual?

Questions and answers

Summary of Contents for Renesas DALI Master Controller GUI

  • Page 1 All information contained in these materials, including products and product specifications, represents information on the product at the time of publication and is subject to change by Renesas Electronics Corp. without notice. Please review the latest information published by Renesas Electronics Corp. through various means, including the Renesas Electronics Corp.
  • Page 2 Renesas Electronics disclaims any and all liability for any damages or losses incurred by you or any third parties arising from the use of any Renesas Electronics product that is inconsistent with any Renesas Electronics data sheet, user’s manual or other Renesas Electronics document.
  • Page 3 Unit Products The following usage notes are applicable to all Microprocessing unit and Microcontroller unit products from Renesas. For detailed usage notes on the products covered by this document, refer to the relevant sections of the document as well as any technical updates that have been issued for the products.
  • Page 4 Intended readers: This manual describes the DALI Master Controller GUI. This manual is intended for users who have general knowledge of Windows. Note that the descriptions in this manual are based on examples using the DALI Master Controller GUI in Windows 10.
  • Page 5 "Provisional" in this manual. Please understand this before using such information. - DALI Master Controller GUI User's Manual (this manual) - RL78/I1A Lighting Communication Master Evaluation Board User's Manual - RX65N Group Application Note DALI-2 Lighting Communications Using Cloud Kit...

  • Page 6: Table Of Contents

    Setup Procedure ............................5 Installing the Visual C++ Redistributable Package ..............6 Required Files ............................6 Installing the Visual C++ Redistributable Package ................. 6 Installing the DALI Master Controller GUI ................7 Installer ..............................7 3.1.1 Installation procedure ..........................7 3.1.2...
  • Page 7 6.4.1 [Control Gear] tab ..........................64 6.4.2 [Control Device] tab ..........................65 Random Address Allocation window ..................... 66 6.5.1 [Control Gear] tab ..........................66 6.5.2 [Control Device] tab ..........................67 Direct Address Allocation window ......................68 6.6.1 [Control Gear] tab ..........................68 6.6.2 [Control Device] tab ..........................

  • Page 8: Introduction

     Sending a user-specified 16-bit Forward Frame when an Event Message is received The DALI master Controller GUI starts in either of two operation modes depending on the connected Lighting Communication Master Evaluation Board and firmware. The following lists and describes the functions available in each operation mode.
  • Page 9 All Device Mode V2.1 or later When the connection with the DALI Master Controller GUI is complete, the title bar shows [Operation mode] and the firmware version of the Lighting Communication Master Evaluation Board connected to ROOT in the address tree.

  • Page 10: Operating Environment

    Note: EZ-0008 is not supported. 1.1.1.3 Additional components To use the DALI Master Controller GUI, you must install the following software in advance. We recommend that you install the latest version of Service Pack irrespective of OS and components. • Microsoft .NET Framework 4.8 Note •...

  • Page 11: Overall Structure

    The following shows an example of overall structure. Connect the DALI Master Controller GUI started on the PC to the Lighting Communication Master Evaluation Board by using a USB cable. After that, DALI communication can be performed via the DALI interface on the Lighting Communication Master Evaluation Board.

  • Page 12: Setup Procedure

    <3> Installing the driver Connecting the Lighting Communication Master Evaluation Board and the PC via USB Installing the driver on the PC (See 3 Installing the DALI Master Controller GUI.) <4> Configuring the COM ports Double-click the [DALI Master Controller GUI] icon to display [DALI Master Controller].

  • Page 13: Installing The Visual C++ Redistributable Package

    (2) Microsoft Visual C++ 2015-2022 redistributable package (64-bit environment) VC_redist.x64.exe 2.2 Installing the Visual C++ Redistributable Package Install the Visual C++ redistributable package required for the DALI Master Controller GUI. The following describes the procedure for installation in Windows 10 (64-bit environment). <1>...

  • Page 14: Installing The Dali Master Controller Gui

    DALI Master Controller GUI 3 Installing the DALI Master Controller GUI 3. Installing the DALI Master Controller GUI This chapter describes how to install the DALI Master Controller GUI. 3.1 Installer The DALI Master Controller GUI has the following installer.

  • Page 15: Uninstallation Procedure

    In the [Start] menu, scroll to [W], and then select [Windows System Tools], [Control Panel], and [Programs and Features]. <2> Select [DALI Master Controller GUI] from the displayed programs, and then display the menu by right- clicking. <3> Click [Uninstall (U)] in the menu.

  • Page 16: Driver

    DALI Master Controller GUI 3 Installing the DALI Master Controller GUI 3.2 Driver Because the drivers are installed by default in Windows, separate installation is not required. R20UT0715EJ0400 Rev.4.00 Page 9 of 82 Nov.9.22...

  • Page 17: Start And Termination

    DALI Master Controller GUI 4 Start and Termination 4. Start and Termination When the Visual C++ redistributable package and DALI Master Controller GUI are installed, you can start the DALI Master Controller GUI. 4.1 Start <1> Connect the Lighting Communication Master Evaluation Board to the host PC.
  • Page 18 DALI Master Controller GUI 4 Start and Termination Figure 4-2 Window at startup (connection communication failed) <5> Click the [OK] button. <6> On the menu bar, select [Settings], [Serial], and then specify the COM port and baud rate. Figure 4-3 DALI Master Controller window <7>...

  • Page 19: Exit

    DALI Master Controller GUI 4 Start and Termination <8> When the connection with the Lighting Communication Master Evaluation Board is successful, you can specify settings. Table 4-1 Recommended baud rate settings for Lighting Communication Master Evaluation Boards Lighting Communication Master Evaluation Boards...

  • Page 20: Operating The Dali Master Controller Gui

    5.1.1 Assigning short addresses The following provides an example of assigning short addresses. <1> Start the DALI Master Controller GUI by double-clicking the [Master Controller GUI] icon. Figure 5-1 Assigning short addresses (1) <2> In the main menu, select [View] and then [Command Log]. The Command Log window appears.
  • Page 21 DALI Master Controller GUI 5 Operating the DALI Master Controller GUI Figure 5-3 Command (menu) <4> The Random Address Allocation window appears. Click the [Start ] button, and then click the [OK] button. Figure 5-4 Random Address Allocation window (1) <5>...
  • Page 22 DALI Master Controller GUI 5 Operating the DALI Master Controller GUI Figure 5-6 Query View window R20UT0715EJ0400 Rev.4.00 Page 15 of 82 Nov.9.22...

  • Page 23: Power Control

    DALI Master Controller GUI 5 Operating the DALI Master Controller GUI 5.1.2 Power Control The [Power Control] field allows you to control lighting for the selected address. Figure 5-7 Power Control Fading is performed for the number of seconds specified for [Fade time].

  • Page 24: Fade Setting

    DALI Master Controller GUI 5 Operating the DALI Master Controller GUI 5.1.3 Fade Setting The [Fade Setting] field allows you to specify the Fade time and Fade rate. The following provides an operation example of turning off the lighting after two seconds of fading for Address 0 with the maximum level (240).
  • Page 25 DALI Master Controller GUI 5 Operating the DALI Master Controller GUI <4> Click the [Max] button to set lighting at the maximum level. Enter "0" in the text box beside the [Direct] button and then click the [Direct] button. The lighting is turned off after two seconds of fading.

  • Page 26: Level Setting

    DALI Master Controller GUI 5 Operating the DALI Master Controller GUI 5.1.4 Level Setting The [Level Setting] field allows you to specify the upper and lower limits of the Actual Level, Power On Level and System Failure Level. The following provides an example of setting Max. Level (254) for Address 0 to Max. Level (240).

  • Page 27: Scene Setting

    [Go to SCENE] button. The lighting level is set to 190 after two seconds of fading. 5.1.6 Device Type Setting You can specify the settings related to the device type (EC62386-2XX). The DALI Master Controller GUI supports the following device types: • Device type 6 (standard: IEC62386-207 ed1.0) • Device type 8 (standard IEC62386-209 ed1.0) R20UT0715EJ0400 Rev.4.00...

  • Page 28: Control Device] Tab

    DALI subnet. 5.2.1 Assigning short addresses The following provides an example of assigning short addresses. <1> Start the DALI Master Controller GUI by double-clicking the [Master Controller GUI] icon. Click the [Control Device] tab. Figure 5-14 Assigning short addresses (1) <2>...
  • Page 29 DALI Master Controller GUI 5 Operating the DALI Master Controller GUI <4> The Random Address Allocation window appears. Click the [Control Device] tab. Click the [Start ] button, and then click the [OK] button. Figure 5-17 Random Address Allocation window (1) <5>...

  • Page 30: Configuration (Device Level)

    DALI Master Controller GUI 5 Operating the DALI Master Controller GUI 5.2.2 Configuration (Device Level) In the [Configuration (Device Level)] field, you can specify the Device Level for the Control Device. The following provides an example of specifying [Enable] for [Power cycle Notification] for Address 0.

  • Page 31: Configuration (Instance Level)

    DALI Master Controller GUI 5 Operating the DALI Master Controller GUI 5.2.3 Configuration (Instance Level) The [Configuration (Instance Level)] field allows you to specify the Instance Level for the Control Device. The following provides an example of specifying [Enable] for the instance of [Instance Number 0] for Short Address 0.

  • Page 32: Instance Type And Feature Type

    You can specify the settings related to the Instance Type (IEC62386-3XX, where XX is 01 to 31) and Feature Type (IEC62386-3XX, where XX is 32 to 96). The current version of the DALI Master Controller GUI does not support any Instance Type or Feature Type. R20UT0715EJ0400 Rev.4.00 Page 25 of 82 Nov.9.22...

  • Page 33: Event Control] Tab

    Event Message. Figure 5-24 [Event Control] tab The DALI Master Controller GUI displays a received Event Message in the [Event Control] tab. By registering a 16-bit Forward Frame corresponding to that message, the registered 16-bit Forward Frame will be automatically sent when the same Event Message is received.
  • Page 34 DALI Master Controller GUI 5 Operating the DALI Master Controller GUI <3> Press the Touch Key of the RL78/G23 to send an Event Message. When the Event Message is received, the received frame is displayed in the [Event Control] tab.
  • Page 35 DALI Master Controller GUI 5 Operating the DALI Master Controller GUI <7> Click to select the [Enable] check box. Figure 5-29 [Event Control] tab operation example (5) <8> In the main menu, select [View] and then [Bus Monitor view]. The Bus Monitor View window appears.

  • Page 36: Window Reference

    DALI Master Controller GUI 6 Window Reference 6. Window Reference 6.1 List of Windows The following shows a list of windows Table 6-1 List of windows Window Description Reference Main window This window is first displayed when the DALI Master Controller GUI starts.

  • Page 37: Main Window

    DALI Master Controller GUI 6 Window Reference 6.2 Main Window 6.2.1 [Control Gear] tab The [Control Gear] tab contains the following function groups. The following describes each function group. Figure 6.1 Main window ([Control Gear] tab) R20UT0715EJ0400 Rev.4.00 Page 30 of 82...
  • Page 38 DALI Master Controller GUI 6 Window Reference 6.2.1.1 Address tree A tree consisting of Broadcast, Groups 0 to 15, and Short Addresses is displayed for Control Gears. The short address of a Control Gear that does not belong to any group is displayed under [Not Assigned].
  • Page 39 DALI Master Controller GUI 6 Window Reference (1) Root selected [Reacquire]: Acquires information about the connected Control Gear and redisplays the address tree. (2) Broadcast selected [Add to Group]: Adds all Control Gears to any Group. [Remove From Group]: Removes all Control Gears from any Group.
  • Page 40 DALI Master Controller GUI 6 Window Reference 6.2.1.2 Power Control The [Power Control] field has buttons for manipulating the Actual Level. Clicking a button in the [Power Control] field sends a command to the selected address. Figure 6-4 Power Control (1) [Max] button Sends the RECALL MAX LEVEL command to the selected address.
  • Page 41 DALI Master Controller GUI 6 Window Reference (6) [Step down] button Sends the STEP DOWN command to the selected address. (7) [Off] button Sends the OFF command to the selected address. (8) [Direct] button Sends the value in the text box to the selected address by using the DIRECT ARC POWER CONTROL command.
  • Page 42 DALI Master Controller GUI 6 Window Reference 6.2.1.3 Fade Setting The [Fade Setting] field contains the drop-down lists used to specify the fade time and fade rate. The specified settings are not sent to the Control Gear unless the [Set] button is clicked.
  • Page 43 DALI Master Controller GUI 6 Window Reference (1) Fade time Select one of the following 16 options in the drop-down list: "0 (no fade)" and "1 (0.707sec)" to "15 (90.510sec)". (The default is empty.) If the selected address is a short address, the set value is displayed.
  • Page 44 DALI Master Controller GUI 6 Window Reference (2) Fade rate Select one of the following 15 options in the drop-down list (the default is empty): "1 (357.796steps/sec)" to "15 (2.795steps/sec)". If a short address is selected, the value specified for this address is displayed.
  • Page 45 DALI Master Controller GUI 6 Window Reference (3) Extended Fade time For [Base] under [Extended Fade time], you can select one of the 16 options "1 (0000B)" to "16 (1111B)" in the drop-down list. For [Multiplier] under [Extended Fade time], you can select one of five options "0 (0msec)"...
  • Page 46 DALI Master Controller GUI 6 Window Reference Table 6-5 Extended Fade time multiplier Setting Fade time multiplier Drop-down list 000B (0ms) 001B (100ms) 010B (1s) 011B (10s) 100B (1min) Note: The default value is "0 (000B(0ms)". R20UT0715EJ0400 Rev.4.00 Page 39 of 82...
  • Page 47 DALI Master Controller GUI 6 Window Reference 6.2.1.4 Level Setting The [Level Setting] field contains the drop-down list and buttons used to specify the upper and lower limits of the Actual Level, , and System Failure Level. Power On Level The specified settings are not sent to the Control Gear unless the [Set] button is clicked.
  • Page 48 DALI Master Controller GUI 6 Window Reference (4) [Set] button The [Set] button is inactive (cannot be clicked) when settings are incomplete Clicking the [Set] button sends one of the following commands to the selected address after sending the DTR0 command.
  • Page 49 DALI Master Controller GUI 6 Window Reference (3) Text box A value from 0 to 255 can be entered (the default value is 255). The value is updated according to the position of the slider on the track bar. The text box is inactive when the [Actual] or [Remove] check box is selected.
  • Page 50 DALI Master Controller GUI 6 Window Reference 6.2.1.6 Device Type Setting The [Device Type Setting] field has buttons that specify settings related to Device Type that is an extended standard of Control Gears. Functions of each supported Device Type are provided on separate tabs.
  • Page 51 DALI Master Controller GUI 6 Window Reference (2) Fast Fade Time Select one of the following 28 options in the drop-down list (the default is empty): "0 (<25msec)" and "1 (25msec)" to "27 (675msec)". Clicking the [Set] button sends the following commands to the selected address.
  • Page 52 DALI Master Controller GUI 6 Window Reference 6.2.1.7 DT8 (209) This tab provides the functions for performing operations on Control Gears extended for Device Type 8. Figure 6-9 Device Type Setting (DT8 (209)) (1) Tc Increment Enter a value in the range from 1 to 100 in the text box. (The default is empty). Clicking the [Set] button sends the following commands to the selected address.
  • Page 53 DALI Master Controller GUI 6 Window Reference Table 6-12 Tc Limit Order of sending Command to be sent DTR0 DTR1 DTR2 ENABLE DEVICE TYPE 8 STORE COLOUR TEMPERATURE TC LIMIT (3) Automatic Activation Clicking the [Enable] or [Disable] button sends the following commands to the selected address.
  • Page 54 DALI Master Controller GUI 6 Window Reference (6) X Step Down Clicking the [X Step Down] button sends the following commands to the selected address. Table 6-16 X Step Down Order of sending Command to be sent ENABLE DEVICE TYPE 8...
  • Page 55 DALI Master Controller GUI 6 Window Reference [Tc] tab (10) Tc Step Cooler Clicking the [X Step Cooler] button sends the following commands to the selected address. Table 6-20 Tc Step Cooler Order of sending Command to be sent ENABLE DEVICE TYPE 8...
  • Page 56 DALI Master Controller GUI 6 Window Reference (14) Temp WAF Enter a value in the range from 0 to 255 in the text box, or specify a value by using three track slider bars. (The default is empty). Clicking the [Set] button sends the following commands to the selected address.

  • Page 57: Control Device] Tab

    DALI Master Controller GUI 6 Window Reference 6.2.2 [Control Device] tab The [Control Device] tab contains the following function groups. The following describes each function group. The [Control Device] tab is available in All Device Mode only. Figure 6.9 Main window ([Control Device] tab) R20UT0715EJ0400 Rev.4.00...
  • Page 58 DALI Master Controller GUI 6 Window Reference 6.2.2.1 Address tree A tree consisting of Broadcast, Groups 0 to 31, Short Addresses, and Instance Numbers is displayed for Control Devices. The short address of a Control Device that does not belong to any group is displayed under [Not Assigned].
  • Page 59 DALI Master Controller GUI 6 Window Reference (1) Root selected [Reacquire]: Acquires information about the connected Control Gear and redisplays the address tree. (2) Broadcast selected [Add to Group]: Adds all Control Devices to any Group. [Remove From Group]: Removes all Control Devices from any Group.
  • Page 60 DALI Master Controller GUI 6 Window Reference 6.2.2.2 Configuration (Device Level) Use this field to specify the Device Level settings. (1) Application Controller Clicking the [Enable] button sends "ENABLE APPLICATION CONTROLLER" to the selected address. Clicking the [Disable] button sends "DISABLE APPLICATION CONTROLLER" to the selected address.
  • Page 61 DALI Master Controller GUI 6 Window Reference 6.2.2.3 Configuration (Instance Level) Use this field to specify the Instance Level settings. (1) Instance Clicking the [Enable] button sends "ENABLE INSTANCE" to the selected instance. Clicking the [Disable] button sends "DISABLE INSTANCE" to the selected instance.
  • Page 62 You can specify the settings related to the Instance Type (IEC62386-3XX, where XX is 01 to 31) and Feature Type (IEC62386-3XX, where XX is 32 to 96). The current version of the DALI Master Controller GUI does not support any Instance Type or Feature Type. R20UT0715EJ0400 Rev.4.00 Page 55 of 82 Nov.9.22...

  • Page 63: Event Control] Tab

    DALI Master Controller GUI 6 Window Reference 6.2.3 [Event Control] tab The [Event Control] tab contains the following table functions. The following describes the table functions. The [Event Control] tab is available in All Device Mode only. Figure 6-12 [Event Control] tab R20UT0715EJ0400 Rev.4.00...
  • Page 64 DALI Master Controller GUI 6 Window Reference 6.2.3.1 Enable Select the check box to register a response frame corresponding to the received Event Message. The [Enable] setting is valid when values are set for [Receive Event] and [Send Frame]. 6.2.3.2 Receive Event The Event Message received on the DALI communication bus is displayed in binary format.
  • Page 65 DALI Master Controller GUI 6 Window Reference (1) Event Response Setting This window is used to select a16-bit Forward Frame to be automatically sent in response to the received Event Message. Select a command to be sent in the drop-down list. Click the [OK] button, select the code, and then close the Event Response Setting window.
  • Page 66 DALI Master Controller GUI 6 Window Reference (5) Code The specified command code is displayed in hexadecimal and binary format. (6) Data Data can be selected according to the selected command. Select a value in the drop-down list. 6.2.3.4 Delete Item Removes the registered Receive Frame and Send Frame.

  • Page 67: Manual Command Window

    DALI Master Controller GUI 6 Window Reference 6.3 Manual Command Window The Manual Command window allows you to select a command to be sent in the drop-down list, and then send the code by clicking the [Send] button. The [Send] button cannot be clicked if the settings are incomplete.
  • Page 68 DALI Master Controller GUI 6 Window Reference 6.3.1.3 Address Select one of the following options to specify Broadcast, Group, Short Address, or Without Short Address. [Broadcast]: Select this item to specify "Broadcast". [Group]: Select this item to specify a Gear Group (selectable from 0 to 15).

  • Page 69: Control Device] Tab

    DALI Master Controller GUI 6 Window Reference 6.3.2 [Control Device] tab This tab is used to send 24-bit Forward Frames for Control Devices. This tab is available in All Device Mode only. Figure 6-16 Manual Command window ([Control Device] tab) 6.3.2.1 Command...
  • Page 70 DALI Master Controller GUI 6 Window Reference 6.3.2.4 Instance Addressing and Dest You can specify the following: Instance number, Instance group, Instance type, Feature on instance number level, Feature on instance group level, Feature on instance type level, Feature broadcast, Feature on instance broadcast level, Feature on device level, Device.

  • Page 71: Manual Command (By Code) Window

    DALI Master Controller GUI 6 Window Reference 6.4 Manual Command (By Code) Window The Manual Command (By Code) window allows you to directly enter a binary command to be sent, and then send the code by clicking the [Send] button. The [Send] button can be clicked after a binary number (16 bits) or hexadecimal number is entered.

  • Page 72: Control Device] Tab

    DALI Master Controller GUI 6 Window Reference 6.4.2 [Control Device] tab This tab is used to send 24-bit Forward Frames for Control Devices. This tab is available in All Device Mode only. Figure 6-18 Manual Command (By Code) window ([Control Device] tab) 6.4.2.1 Command...

  • Page 73: Random Address Allocation Window

    DALI Master Controller GUI 6 Window Reference 6.5 Random Address Allocation window The Random Address Allocation window displays a list of random addresses and assigned short addresses of the target device. The Random Address Allocation window is displayed by selecting [Command] and then [Random Address Allocation] in the main menu.

  • Page 74: Control Device] Tab

    DALI Master Controller GUI 6 Window Reference 6.5.2 [Control Device] tab This tab is used to perform Random Address Allocation for the target Control Device. This tab is available in All Device Mode only. Figure 6-20 Random Address Allocation window ([Control Device] tab).

  • Page 75: Direct Address Allocation Window

    DALI Master Controller GUI 6 Window Reference 6.6 Direct Address Allocation window The Direct Address Allocation window allows you to directly assign a short address. When using this function, make sure that only one target DALI device is connected to the DALI subnet.

  • Page 76: Control Device] Tab

    DALI Master Controller GUI 6 Window Reference 6.6.2 [Control Device] tab This tab is used to perform Direct Address Allocation for the target Control Device. This tab is available in All Device Mode only. Figure 6-22 Direct Address Allocation window ([Control Device] tab) 6.6.2.1 Short Address...

  • Page 77: Command Log Window

    DALI Master Controller GUI 6 Window Reference 6.7 Command Log Window The Command Log window displays the sent commands and their responses in text format. To close the Command Log window, click The Command Log window is displayed by selecting [View] and then [Log] in the main menu.
  • Page 78 DALI Master Controller GUI 6 Window Reference Select the storage folder, and then specify the name of the file to be saved. (CSV format files can only be saved.) Clicking the [Save (s)] button starts saving of log data from that point of time.
  • Page 79 DALI Master Controller GUI 6 Window Reference Table 6-34 Response result (abnormal) Display Meaning Sending Error Retry limit exceeded during resend processing due to a timing violation Sending Timeout Unsent status continued for a certain period of time (due to a...

  • Page 80: Bus Monitor View Window

    DALI Master Controller GUI 6 Window Reference 6.8 Bus Monitor View Window The Bus Monitor View window displays all communication frames and abnormality information generated on the DALI communication bus. To close the Bus Monitor View window, click the button on in the upper right corner of the window.

  • Page 81: Displayed Information

    DALI Master Controller GUI 6 Window Reference 6.8.2 Displayed information Figure 6-27 Information displayed in the Bus Monitor View window Table 6-37 Displayed information (abnormal) Display Description bit timing violation detected A bit timing violation is received. corrupted backward frame received A corrupted backward frame is received.

  • Page 82: Query View Window

    DALI Master Controller GUI 6 Window Reference 6.9 Query View Window The Query View window displays the settings of each slave. To close the Query View window, click The Query View window is displayed by selecting [View] and then [Query] in the main menu.

  • Page 83: Control Device] Tab

    DALI Master Controller GUI 6 Window Reference 6.9.2 [Control Device] tab Figure 6-29 Query View window (Control Device) 6.9.3 Query When Broadcast is selected, a list of all short addresses is displayed. When a group is selected, a list of short addresses belonging to that group is displayed.

  • Page 84: Serial Window

    DALI Master Controller GUI 6 Window Reference 6.10 Serial Window This window is used to configure a serial port. A connection is not established if the previous configuration information is not found. The Serial window is displayed by selecting [Setting] and then [Serial] in the main menu.

  • Page 85: Change Address Window

    DALI Master Controller GUI 6 Window Reference 6.11 Change Address Window This window is used to change a short address. When an address (0 to 63) is selected, clicking the [OK] button changes the address. See Figure 6-3 Address tree (right-click menus on the [Control Gear] tab).

  • Page 86: Version Window

    6 Window Reference 6.12 Version Window This window is used to confirm the version of the DALI Master Controller GUI. The Version window is displayed by selecting [Help] and then [Version] in the main menu. Clicking the [OK] button closes the Version window.

  • Page 87: Menus

    DALI Master Controller GUI 6 Window Reference 6.13 Menus 6.13.1 File Figure 6-33 File (menu) [Exit]: Exits the DALI Master Controller GUI. 6.13.2 Command Figure 6-34 Command (menu) [Manual Command]: Displays the Manual Command window. (See 6.3 Manual Command Window.) [Send Code]: Displays the Manual Command (By Code) window.

  • Page 88: View

    DALI Master Controller GUI 6 Window Reference 6.13.3 View Figure 6-35 View (menu) [Command Log]: Displays the Command Log window. (See 6.7 Command Log Window.) [Bus Monitor View]: Displays the Bus Monitor View window. (See 6.8 Bus Monitor View Window.) [Query View]: Displays the Query View window.

  • Page 89: Help

    DALI Master Controller GUI 6 Window Reference 6.13.5 Help Figure 6-37 Help (menu) [Version]: Displays the Version window. (See 6.12 Version Window.) R20UT0715EJ0400 Rev.4.00 Page 82 of 82 Nov.9.22...
  • Page 90 Revision History DALI Master Controller GUI Rev. Date Description Page Summary 1.00 Mar.01.09 First Edition issued － 2.00 Mar.23.12 Second Edition issued － 3.00 Mar.31.16 Correspondence of IEC62386-102ed2.0 and IEC62386-207ed1.0 － 4.00 Nov.9.22 Correspondence of IEC62386-209 and RX65N cloud kit －...
  • Page 91 DALI Master Controller GUI User's Manual Publication Date March 1, 2009 Rev.1.00 March 23, 2012 Rev.2.00 March 31, 2016 Rev 3.00 November 9, 2022 Rev 4.00 Published by Renesas Electronics Corporation...
  • Page 92 DALI Master Controller GUI R20UT0715EJ0400...

Table of Contents