Vorel 73410 - Gas Burner Manual

PARTS DESCRIPTION

1. gas tank
2. gas regulator
3. switch
4. gas nozzle
5. tip basis
6. tip of the soldering tool
7. support of the device
8. gas tank filling valve
9. fixing ring

PROPERTIES OF THE TOOL

The gas burner has been designed for soldering, heating or drying. Since it is fed with propane and butane cartridges, it is possible to operate the tool where there is no source of electric energy. Compact dimensions and low weight permit a comfortable and safe operation. The tool has been designed solely for domestic use and must not be used professionally, i.e. in plants or for commercial purpose. A correct, reliable and safe operation of the tool depends on its correct use, so:

Read the operating manual thoroughly in order to get acquainted with the tool before it is connected to the gas cartridge. Keep the manual for future reference.

The supplier shall not be held responsible for any damage occurred as a result of failure to observe safety regulations and indications contained in this manual.

ACCESSORIES

The tool is delivered complete and does not require assembly. The tool is supplied with an empty gas tank.

TECHNICAL PARAMETERS

SAFETY RECOMMENDATIONS

The tool may be used only with butane or a propane-butane mixture. The tool has its own tank, which must be filled with either gas. Filling must be carried out from pressurised containers by means of an adequate adapter, provided along with containers.
Do not ever fill the tank without having previously read the instructions printed on the container.
The original structure and settings must not be modified. An attempt to modify the settings or the structure of the unit and remove certain elements or using them for other purposes than intended may be dangerous.
Do not use the device if the sealing is damaged or worn out. Do not use the device, if it is untight, damaged or if it is not functioning correctly. Do not use the device which bears any sign of damage.
Close the valves of the unit before filling the tank with gas. Do not smoke while changing gas cartridges.
The tool must be operated in well ventilated areas, in accordance with national regulations regarding: supply of air for burning; avoidance of dangerous gathering on unburnt gases.
The tool should be used far from inflammable materials. Keep a minimum distance of 5 metres between the outlet of the burner and the nearby surfaces (walls, ceilings). Do not ever direct the outlet of the burner towards people or animals.
The gas tank must be filled in well ventilated places, preferably outdoors, far from any sources of fire, such as open flames, pilot burners, electric heaters and away from other people.
If the tool is not tight (you can smell gas), then remove it immediately outdoors to a well-ventilated place containing no source of fire, where the leakage may be localized and eliminated. If you want to check any leakage of the tool, do it outdoors. Do not try to detect leakage using flames. To do so use water with soap.
During work the outlets of the burners heat up to a high temperature. Keep children and bystanders away from the tool.
Before you proceed to fill the gas tank, make sure the gas burners are off.
Do not modify the tool.
In case the tool must be sent to the manufacturer or a service point, it is required to cool it down, empty the gas tank and then place the in its case and protect it adequately for the given means of transport.
It is prohibited to send the tool along with the tank filled with gas. Transport of dangerous materials is subject to restrictions.
Do not put a burning burner down. Do not heat up gas cartridges or burn hoses. Replace the accessories, if necessary.
Do not work indoors; provide good ventilation. Work only in a clean area, away from inflammable or greasy materials. Wear eye protection. Do not wear greasy clothes. Avoid welding and soldering fumes.
During work observe indications regarding: gas consumption (at normal settings) adequately for each of the accessories and the shelf life of the gas tanks.
Empty the gas tank, if the unit is not to be used for a long period or in case it is transported in a vehicle.
Store and transport gas cartridge upright. Protect them from children.
Use only specified spare parts. Do not ever use a unit with a damaged element.
Service point: TOYA SA, ul. Sołtysowicka 13-15, 51-168 Wrocław, Poland.
In case of a gas leakage, it is required to immediately turn the burner off and walk away from any source of fire and high temperature. Proceed in accordance with the information contained in safety data sheet provided along with the gas cartridge. Head against the wind. Isolate the contaminated area and keep bystanders away. Try to stop or at least reduce the emission to the environment, if possible. Use adequate protection of the respiratory tract. Spray water mist to minimise and limit the release of gas.

OPERATION OF THE TOOL

Filling the gas tank (II)

Filling the gas tank should be realised outdoors or in a well-ventilated room, far from sources of fire or excessive heat. Maintain a safe distance from bystanders.
Close the gas valve, turning the handwheel of the regulator to the limit towards the symbol „1" and make sure the switch is „OFF".
Use high quality gas. The gas container should be equipped with an adapter adequate for the kind of valve.
Place the gas burner with the valve pointing upwards. Place the outlet of the gas container at the valve. Press the container to the valve. Continue filling the tank until the first signs of overfilling are noticed, when gas starts to come out from the connection between the gas burner and the gas container. Put the gas burner down for a couple of minutes in order for the pressure of the gas in the tank to stabilise.

Work with the tool

The tool may be used both as a gas burner and as a soldering tool or a hot air gun.

In case of its being used as a gas burner, it is required to dismantle the tip of the soldering tool along with the base, unscrewing the plastic ring.
Make sure there is no gas leakage, and then slightly turn the handwheel of the regulator towards the symbol „4". Turn the switch ON, and then using an appropriate external lighting device light the gas coming out of the outlet of the gas burner nozzle (III).

Adjust the height of the flame with the gas regulator.

In case the device is applied as a soldering tool, make sure the tip of the soldering tool along with the base, unscrewing the plastic ring. Check also the connection of the tip to the base.
Make sure there is no gas leakage, and then slightly turn the handwheel of the regulator towards the symbol „4". Turn the switch ON, and then using an appropriate external lighting device light the gas coming out of the outlet of the gas burner nozzle. Turn the switch ON, and then using an appropriate external lighting device light the gas coming out of the outlet of the gas burner nozzle (IV).


Release the tip base, and then the base will return to the working position thanks to the internal spring. Adjust the height of the flame with the gas regulator. Wait approximately one minute until the tip is hot. In case the device is used as a hot air gun, proceed as in the case of soldering tool, but the tip must be dismantled from the base (V).

Turning the lamp burner off

Turn the handwheel of the regulator to the limit towards the symbol „OFF". Make sure the flame has been put out. Unfold the support and leave the tool to cool down. Attention! It is prohibited to cool the device with a stream of water.

OPERATION OF THE DEVICE

Filling the gas tank (II)

Filling the gas tank must be realised outdoors or in a well-ventilated room, far from sources of fire or excessive heat. Maintain a safe distance from bystanders.
Close the gas valve, turning the handwheel of the regulator to the limit towards the symbol „-" and make sure the switch is OFF. Dismantle the base of the gas burner.
Use high quality gas. The gas container should be equipped with an adapter adequate for the kind of valve. Place the gas burner with the valve pointing upwards. Place the outlet of the gas container at the valve. Press the container to the valve. Continue filling the tank until the first signs of overfilling are noticed, when gas starts to come out from the connection between the gas burner and the gas container. Put the gas burner down for a couple of minutes in order for the pressure of the gas in the tank to stabilise. Install the base (III).

Work with the tool

Make sure there is no gas leakage, and then slightly turn the handwheel of the regulator towards the symbol „+". Set the value in the middle of the operating range. Pull out the safety device of the switch (IV), and then press it and hold it pressed. The internal lighting tool will light gas at the gas burner nozzle. Adjust the height of the flame with the gas regulator.
The work mode selector permits instantaneous or continuous operation. In case of instantaneous operation it must be turned „OFF". In this mode the switch must be held all the time, and once it is released the gas flow is cut off and the flame is put out. Continuous operation is possible when the selector is set to „CONTINOUS". In such a case if the switch is released the gas supply is not cut off. This permits operation, when continuous supply of gas for a prolonged period of time is required.

Putting the gas burner out

In case of instantaneous operation, it is sufficient to release the switch, and then the gas flow is cut off and the flame is put out. In case of continuous operation the operation switch must be moved to „OFF", and then the gas flow is cut off and the flame is put out.
Leave the tool on the support in a vertical position, so that it cools down.
Attention! It is prohibited to cool the device with a stream of water.

Maintenance of the device

The tool must be cleaned with a soft and humid cloth. Heavy dirt must be removed with soap diluted in water. Do not use abrasive cleaning agents. Do not use chemicals and cleaning liquids. In case of any damage and dirt in the nozzle, it is required to contact a service workshop of the manufacturer. It is prohibited to clean the nozzle alone, particularly using sharp objects.
Do not modify the device. Do not use the device with damaged elements.

Storage

The tool must be stored in the provided individual cases in a dark, well-ventilated and dry place, not accessible to third parties, particularly children. Store the vertically. Do not expose the tool to temperatures exceeding 50 ⁰C and avoid prolonged exposure to direct sunlight.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Vorel 73410 - Gas Burner Manual