ProLogic C Series Alarm Sets Manual

Specifications

Battery type(s)
*Alarm: 9V battery
*Receiver: 3 1.5V AAA batteries
*Bivvy light: 3.7V battery, 2.600mAh LiOn

Transmitter power output in mW: less than 10mW

Operating Voltage:
* Alarm: 9V
*Receiver: 4.5V
*Bivvy light: 3.7V

Standby current in uA:
*Alarm: 6uA
*Receiver: 2mA
*Bivvy light: 35uA

Working current in mA:
*Alarm: 10mA
*Receiver: 20mA
*Bivvy light: 30mA

Transmission/transmitter: FM

Operating frequency: 433.92MHz

Effective working distance of transmission: 100M

ALARM

OPERATING INSTRUCTIONS

1. Press and hold button V to switch the alarm ON or OFF.
2. Press button V to adjust the volume (including silent).
3. Press button T to adjust the tone.
4. Press button S to adjust the sensitivity,
5. Press button L to turn ON or OFF the night light.

RECEIVER

OPERATING INSTRUCTIONS

1. Hold power button to switch the receiver ON or OFF.
2. Press V to adjust volume (including silent).
3. Long press V to turn vibration ON or OFF.

The tone of the receiver is synchronized with the alarm it is paired with.

PAIRING UP THE ALARMS AND RECEIVER

1. Turn on all the alarms that need to be paired.
2. Turn off the receiver, press and hold power button and button V until the LED lights up.
3. Rotate the roller of the alarm you wish to pair first. If successfully paired, the receiver will beep once and the next LED of the receiver will lights up.
4. Rotate the roller of the next alarm until the receiver beeps and the next LED shows. Once 4 alarms are paired, the receiver will turn off automatically.
5. If you only want to pair 2 or 3 alarms to the receiver, once these alarms are paired, press the button V until the LEDs of the receiver go out.

The next time you switch on the receiver, it will still be paired with your alarms. Please note: every time the receiver enters pairing situation, the previous setting will be deleted.

BIVVY LIGHT

OPERATING INSTRUCTIONS

1. Press and hold the ON/OFF button for one second to turn ON or OFF the bivvy light.
2. Turn on the bivvy light, then short press the ON/OFF button to control the delay times: 5, 10 or 20 seconds.
3. When the bivvy light is ON, short press the brightness control button to change the brightness (4 levels). Press and hold the brightness control button for one second and all the white LEDs will enter into sleep mode. They will light up immediately when receiving the signals from a paired C-SERIES alarm.

Battery charging: the red led will light when charging. When full charged, the blue LED will light.

PAIRING UP THE ALARMS AND BIVVY LIGHT

1. Turn on all the alarms that need to be paired.
2. Turn off the bivvy light, press and hold the ON/OFF button and brightness control button until the red LED lights up.
3. Rotate the roller of the alarm you wish to pair first. If successfully paired, the green led of the bivvy light will light up.
4. Rotate the roller of the next alarm until the next LED shows. Once 4 alarms are paired, the bivvy light will turn off automatically.
5. If you only want to pair 2 or 3 alarms to the bivvy light, once these alarms are paired, press the ON/OFF button until the LEDs of the bivvy light go out.

The next time you switch on the bivvy light, it will still be paired with your alarms. Please note: every time the bivvy light enters pairing situation, the previous setting will be deleted.

Videos

Prologic C-series Alarm Review Video

Prologic C-Series Alarms and Alarm Sets - Carp Fishing Video

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download ProLogic C Series Alarm Sets Manual