Summary of Contents for Waukesha Cherry-Burrell SPXFLOW 300 Series
Page 1
INSTRUCTION MANUAL 300 and 350 Series Ball Valve MANUAL AND PNEUMATIC ACTUATORS READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. FORM NO.: 95-03097 REVISION: 10/2020...
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Table of Contents Warranty ................................4 Shipping Damage or Loss ..............................4 Warranty Claim ................................4 Safety ................................5 Care of Component Materials ......................... 6 Stainless Steel Corrosion ...............................6 Elastomer Seal Replacement Following Passivation .....................6 Introduction ..............................
® Warranty Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Warranty LIMITED WARRANTY: Unless otherwise mutually agreed to in writing, (a) SPX FLOW US, LLC (SPX FLOW) goods, auxiliaries and parts thereof are warranted to the Buyer against defective workmanship and material for...
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Safety Safety READ AND UNDERSTAND THIS MANUAL PRIOR TO INSTALLING, OPERATING, OR SERVICING THIS EQUIPMENT SPX FLOW recommends users of our equipment and designs follow the latest Industrial Safety Standards. At a minimum, these should include the industrial safety requirements established by: 1.
® Care of Component Materials Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Care of Component Materials NOTE: SPX FLOW recommends the use of an FDA-approved anti-seize compound on all threaded connections. WARNING Failure to comply with the Care of Component Materials could lead to bodily injury.
Models and Specifications The Waukesha Cherry-Burrell brand 300 Series 2-Way Ball Valve is available with a manual handle, rack and pinion actuator, or linear actuator. The Waukesha Cherry-Burrell brand 350 Series 3-Way Ball Valve is available with a manual handle or rack and pinion actuator.
® Installation Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Installation Air Supply Install the valves using dry, filtered air. Lubrication is not required. If using lubricated air, refer to the solenoid manufacturer’s specifications. The air supply requirements are as follows: •...
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Maintenance Maintenance Maintenance Intervals Maintain adequate stock of replacement parts. See the items listed under "Replacement Kits" on page 19 for 300 Series 2-Way Ball Valves, and page 23 for 350 Series 3-Way Ball Valves.
® Maintenance Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve 300 Series 2-Way Ball Valve Disassembly VA100-745 a Figure 2 - 300-Series 2-Way Ball Valve 1. Remove the nut and washer (Figure 2, items 9 and 10) and Table 1: Callouts for Figure 2 slide off the manual handle (item 11).
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Maintenance 300 Series 2-Way Ball 1. See Figure 2 on page 10. Slide the thrust washer (item 14) over the stem (item 13). Holding the stem threads up, guide Valve Assembly the stem from inside the body (item 4) up through the center hole.
® Maintenance Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve 300 Series 2-Way Ball Mounting a Rack & Pinion actuator on the 300 Valve Actuator Assembly Series 2-Way Manual Ball Valve 1. Per the instructions in step 1 on page 10, remove the handle nut and handle from the ball valve.
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Maintenance Mounting a Linear actuator on the 300 Series 2- Way Manual Ball Valve 1. Per the instructions in step 1 on page 10, remove the handle nut and handle from the ball valve.
® Maintenance Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve 350 Series 3-Way Ball 1. Remove the handle nut (item 2) and slide off the manual handle (item 1). Valve Disassembly 2. Using a socket wrench, remove the lock nut (item 4), then tip the valve upside down to retrieve the bevel washer (item 3) and stainless ring (item 5).
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Maintenance 350 Series 3-Way Ball Please refer to Figure 5 on page 14. Valve Assembly 1. With the Teflon™ ring and stem O-ring (items 9 and 10) installed on the stem (item 11), insert the stem through the inside of the body through the gland port, facing the exposed threads away from the product contact area.
® Maintenance Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve 350 Series 3-Way Ball Mounting an actuator on the 350 Series 3-Way Valve Actuator Assembly Manual Ball Valve 1. See Figure 6. Remove the handle nut (item 2), then remove the handle (item 1) from the ball valve.
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Maintenance Air/Spring Rack & Pinion actuator factory setting orientations with no air on the valve L-Port Valves Normally Open (NO) Normally Closed (NC) VA100-758 VA100-757 T-Port Valves Normally Open (NO)
® Parts Lists Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Parts Lists 300 Series 2-Way Ball Valve with Manual Handle VA100-745 * included in Repair Kit Components not identified in the illustration above are not available individually. See "Complete (Assembled) Valve with Handle"...
Page 19
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Parts Lists 300 Series 2-Way Ball Valve with Manual Handle Valve Size Item # Qty. Part Description Note 1/2" 3/4" 1" 1 1/2" Gasket See Repair Kit Ball Seat See Repair Kit...
® Parts Lists Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Replacement Kits - 350 Series 3-Way Ball Valve with Manual Handle Replacement Kits Part Number Valve size Old Style New Style (pre-May 2015) (starting May 2015) Kits include items marked with * in the parts 1/2"...
® Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Parts Lists 350 Series 3-Way Ball Valve with Rack and Pinion Actuator 3, 3a, 3b VA100-752 Item # Part Description 1/2" 3/4" 1" 1 1/2" 2" 2 1/2" 3" 4"...
Page 26
® Parts Lists Waukesha Cherry-Burrell Brand 300 and 350 Series Ball Valve Notes Page 26 95-03097 10/2020...
Page 28
300 and 350 Series Ball Valve MANUAL AND PNEUMATIC ACTUATORS SPX FLOW 611 Sugar Creek Road Delavan, WI 53115 P: (262) 728-1900 or (800) 252-5200 F: (262) 728-4904 or (800) 252-5012 E: wcb@spxflow.com SPX FLOW, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation.