Related Manuals for LSC MDR Series
Summary of Contents for LSC MDR Series
- Page 1 User Manual LSC Control Systems © +61 3 9702 8000 info@lsccontrol.com.au Version 1.4 www.lsccontrol.com.au March 2023...
- Page 2 Information contained in this manual is subject to change without notice. In any event, LSC Control Systems Pty Ltd cannot be held liable for any direct, indirect, special, incidental, or consequential damages or loss whatsoever (including, without limitation, damages...
-
Page 3: Table Of Contents
MDR DMX-RDM Splitter User Manual Contents INTRODUCTION ..................4 Overview ........................4 Models ........................4 Mounting and Connections .................5 Rack Mount ........................ 5 Truss Mount ....................... 5 Front Panel ......................... 5 DMX Connections ....................... 6 Power Connection ...................... 6 RDM Operation......................6 Connecting Multiple Splitters .................. -
Page 4: Introduction
As of February 2021, all MDR models are supplied with RDM capability as standard. Prior to February 2021, RDM capability was an option for MDR splitters. The RDM option can still be retro fitted to older MDR splitters. Contact your LSC agent for details on how to purchase and install the RDM option. -
Page 5: Mounting And Connections
MDR DMX-RDM Splitter User Manual Mounting and Connections 2.1 Rack Mount MDRX, MDRR and MDRJ model splitters can be mounted in a standard 19 inch rack. They can also be placed on any flat surface. 2.2 Truss Mount MDRT model splitters can be placed on any flat surface or can be mounted to a truss, handrails and pipes using either of two methods. -
Page 6: Dmx Connections
MDR DMX-RDM Splitter User Manual Front Panel LED’s Indication POWER On when power is present DMX INPUT On when DMX data is present on the input DMX TERM On when the DMX TERM switch is ON RDM ENABLE On when RDM is ENABLED Flashes if RDM data overflows. -
Page 7: Connecting Multiple Splitters
MDR DMX-RDM Splitter User Manual If RDM data overflows, the RDM enable LED will begin flashing and the RDM function will be disabled automatically. If an RDM device causes the RDM data stream to overflow you must isolate the offending device from the network and reset the RDM module in the MDR splitter by switching the RDM enable switch OFF, then back ON. -
Page 8: Dmx Information
Cat 5 UTP (Unshielded Twisted Pair) and STP (Shielded Twisted Pair) cable is acceptable. If you want to make your own cables, LSC recommends using Beldon 9842 (or equivalent). The end of the DMX line must be terminated (120 Ω) to prevent the signal reflecting back up the line and causing possible errors. -
Page 9: Wireless Dmx512 Operation
RDM-enabled DMX512-A data splitters. Wireless DMX512 Operation Note: This option is no longer supported or supplied by LSC. This information is only supplied for earlier MDR splitters that were fitted with this option. For full wireless DMX512-A operation, please refer the manufacturer’s websites: Wireless Solutions (W-DMX) www.wirelessdmx.com... -
Page 10: Models
6. The SHoW DMX also allows you to change the Power setting. You will not need to change the setting as this will be set by LSC prior to the unit leaving the factory. Models... -
Page 11: Compliance Statements
Conforms to CE Regulations RCM (Australian) approved Compliance Statements The MDR DMX Splitter range from LSC Control Systems Pty Ltd meets all required CE (European), RCM (Australian) and UKCA (United Kingdom) standards. CENELEC (European Committee for Electrotechnical Standardization). Australian RCM (Regulatory Compliance Mark).