Summary of Contents for TCK SJE10
- Page 1 ORIGINAL INSTRUCTIONS CORDLESS GARDEN SAW SJE10 INSTRUCTIONS MANUAL READ THIS INSTRUCTIONS MANUAL BEFORE USE OF THE TOOL TCK GARDEN 32 rue, Aristide Bergès – ZI 31270 Cugnaux - France Tel: +33 (0)5.34.502.502 Fax : +33 (0)5.34.502.503...
-
Page 2: Safety Warnings
1. SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 3 c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
- Page 4 Use extreme caution when cutting brush and saplings. The slender material may catch the saw blade and be whipped toward you or pull you off balance. Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery causing loss of control.
- Page 5 Residual risk Even if you are operating this product in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this product: 1. Health defects resulting from vibration emission if the product is being used over long periods of time or not adequately managed and properly maintained.
-
Page 6: Your Product
2. YOUR PRODUCT a. Description 1. Cutting Blade 2. Clamping Jaw 3. Shoe 4. Locking button for clamping jaw 5. Blade Holder 6. Safety Switch 7. Trigger 8. Battery pack 9. Battery Release Tab 10. Battery Charger... - Page 7 b. Technical data Voltage 10.8 V d.c. Speed 0-2500/min Operating time (no load) 30 min Stroke length 20 mm Max cutting width 80 mm Blade 152 mm Sound power level Lwa: 90dBb(A) K= 3dBb(A) Sound pressure level Lpa: 79dBb(A) K= 3dBb(A) Vibration Information: ...
- Page 8 3. ASSEMBLY Warning! Ensure the battery is disconnected from the tool before performing any of the following operations The clamping jaw allows branches to be gripped, providing cutting of unsupported branches easier. When cutting wider branches or timber, the clamping jaw can be removed and the garden saw can be used as a standard reciprocating saw.
- Page 9 b. Removing the clamping saw Press and hold the locking button for clamping jaw into the unlock position. Pull the clamping jaw away from the saw body. c. Cutting blades Caution! Do not handle blades without gloves as they are sharp and can become hot after use, potentially causing personal injury Fitting a cutting blade The garden saw can be fitted with standard reciprocating saw blades, therefore can be...
- Page 10 Release the ring on the blade holder and ensure the blade is secure by pulling on the blade d. Removing the cutting blade Rotate and hold the ring on the blade holder anticlockwise. Remove the cutting blade from the blade holder.
- Page 11 Plug the charger into a power socket and the red charging light should illuminate. Once battery fully charged the green light will illuminate. Note: It will take 4-5 charging cycles before the battery reaches optimum charge and run time. Installing and removing the battery ...
- Page 12 4. USE a. Switching the saw on and off Push the safety switch in from either side of the tool and then squeeze the trigger to start the garden saw. Release the trigger to stop the garden saw. b.
- Page 13 Place the branch in between the clamping jaws and then lower to perform the cut. c. Cutting without the clamping jaw When cutting thicker branches or sawing wood or plastic the clamping jaws can be removed to prevent them getting in the way of the cut. See page 7 to see how to remove the clamping saw.
-
Page 14: Maintenance And Storage
5. MAINTENANCE AND STORAGE When not in use, the tool should be stored in a dry, frost free location, keep out of children’s reach. Keep ventilation slots of the saw clean at all times and prevent anything from entering. ... - Page 15 32, rue Aristide Bergès – 31270 Cugnaux - France Tel: +33 (0)5.34.502.502 Fax: +33 (0)5.34.502.503 Declare that the following machine: CORLDESS GARDEN SAW Model: SJE10 Serial Number: Is in conformity with the requirement of the Directive Machine 2006/42/EC And also in conformity with the following Directive:...