Trane Technologies KIT15864 Installation Manual

Bacnet communication interface for reliatel controllers (bci-r)

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Installation Guide

BACnet® Communication Interface

for ReliaTel™ Controllers (BCI-R)

For use with Voyager,™ Odyssey,™ and

Precedent™ rooftop units

Ordering Number: KIT15864

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of

heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and training.

Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury.

When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are

attached to the equipment.

April 2020

SAFETY WARNING

RF-SVN03F-EN

Table of Contents

Need help?

Do you have a question about the KIT15864 and is the answer not in the manual?

Questions and answers

Summary of Contents for Trane Technologies KIT15864

Page 1 ReliaTel™ Controllers (BCI-R) For use with Voyager,™ Odyssey,™ and Precedent™ rooftop units Ordering Number: KIT15864 SAFETY WARNING Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and training.
Page 2 Introduction Read this manual thoroughly before operating or servicing this unit. WARNING Proper Field Wiring and Grounding Warnings, Cautions, and Notices Required! Safety advisories appear throughout this manual as Failure to follow code could result in death or serious required. Your personal safety and the proper operation of injury.
Page 3 Introduction WARNING Follow EHS Policies! Failure to follow instructions below could result in death or serious injury. • All Trane personnel must follow the company’s Environmental, Health and Safety (EHS) policies when performing work such as hot work, electrical, fall protection, lockout/tagout, refrigerant handling, etc.
Page 4: Table Of Contents
Table of Contents Overview ....... 5 BACnet Protocol ......5 Field Kit Parts, Specifications, Dimensions, and Components .
Page 5: Overview
Overview This installation document contains information about the • Provide customers the flexibility to choose the best BACnet Communication Interface for rooftop air possible vendor for their building subsystems. conditioning units with ReliaTel unit control. • Easily incorporate Trane products into legacy non- The following Trane products are supported: Trane systems in existing buildings.
Page 6: Field Kit Parts, Specifications, Dimensions, And Components
Field Kit Parts, Specifications, Dimensions, and Components Field Kit Parts, Specifications, Dimensions, and Components Field Kit Parts – X19051278010 (Voyager II, Odyssey, and Precedent) • One (1) BCI-R Integration Guide (BAS-SVP09-EN) Prior to installation, open the box and verify that the Important: Contact the Trane Parts Center nearest your following parts are enclosed:...
Page 7: Dimensions And Components
Field Kit Parts, Specifications, Dimensions, and Components Dimensions and Components Dimensions: The length and width of the controller are shown here 5.5 in (139.7 mm) width 24VAC - MODBUS + SERVICE STATUS MODBUS LINK The maximum depth of the TX RX C 2010 TRANE REV 02...
Page 8: Mounting And Installing The Controller
Mounting and Installing the Controller Mounting and Installing the Controller Important: Read the following safety warnings prior to Notes: In addition to these instructions, refer to the installation. Procedures presented in this specific rooftop unit literature when installing guide should be performed only by the controller.
Page 9 Mounting and Installing the Controller Figure 2. Voyager III Commercial (all units) BCI-R Figure 3. Precedent: (T/Y)SC(072-120)E, (T/Y)HC(048-072)E, WSC(060-090)E BCI-R RF-SVN03F-EN...
Page 10 Mounting and Installing the Controller Figure 4. Precedent: (T/Y)SC(036-060)E, (T/Y) HC036E, WSC(036-048)E BCI-R Figure 5. Precedent: (T/Y)HC(092-120)E, WSC120E BCI-R RF-SVN03F-EN...
Page 11 Mounting and Installing the Controller Figure 6. Odyssey (6-12.5 ton) BCI-R Figure 7. Odyssey (15-20 ton) BCI-R RF-SVN03F-EN...
Page 12: Setting Addresses Using Rotary Switches
Setting Addresses Using Rotary Switches Setting Addresses Using Rotary Switches There are three rotary switches on the front of the BCI-R For more information about rotary switches, see “Understanding Rotary Switch Values and BACnet Device controller that are used to define a three-digit address when the BCI-R is installed on a BACnet communications IDs,”...
Page 13: Field Wiring Procedures
Field Wiring Procedures Field Wiring Procedures Connecting the Factory Wiring Important: Use 18 AWG, (24 pF/ft. max), communication wire (Trane purple wire); Harness strip no more than 2 in. (5 cm) of the outer conductor of shielded wire. For more 1.
Page 14: Terminator Wiring
Field Wiring Procedures Figure 10. BACnet wiring BARCODE LABEL LED9 LED8 X136 BACNET X100 LINK ADDRESS SETTING TERMINATOR BACnet terminal block Shield wire Terminator Wiring 2. Run communication link wiring from the BACnet terminal block to the BACnet terminator. The BCI-R controller has a built in end-of-line termination 3.
Page 15: Wiring The Air-Fi ™ Wireless Communications Interface (Wci)
Field Wiring Procedures 7. Remove power from the entire unit to ensure that all 9. Restore power to the unit. circuits are unpowered. 8. Connect the IMC wires (gray and blue) to the BCI-R controller and the ground and the 24 Vdc/Vac wires (black and red) as shown in Figure Figure 12.
Page 16: Configuring The Bci-R
Configuring the BCI-R Configuring the BCI-R Using the BACnet Setup Tool The BCI-R can be configured with either the Tracer BACnet Setup Tool or the Tracer TU service tool. This section describes how to configure the BCI-R Note: The BCI-R controller is fully configured from the controller using the Tracer BACnet Setup Tool.
Page 17: Understanding Rotary Switch Values And Bacnet Device Ids
Configuring the BCI-R The Tracer TU splash screen appears briefly followed by the Connect dialog box. Figure 14. Connect dialog box 3. Select the Direct Connection (USB cable) radio button Understanding Rotary Switch if it is not already selected. Values and BACnet Device IDs 4.
Page 18 Configuring the BCI-R • The Tracer SC created a BACnet device ID of 101030. • The BCI-R is installed on link 1. • The Tracer SC address is “0,1,0”. Figure 15. Example showing rotary switch value and BACnet device ID Rotary switch value BACnet device ID RF-SVN03F-EN...
Page 19: What To Do After Adding Options Or Equipment To The Unit
Configuring the BCI-R What To Do After Adding Options cursor near the left edge of the gray bar, keeping the cursor inside the bar; click on this area. A Clear or Equipment to the Unit Controller button will appear in the upper right portion of the screen display.
Page 20: Managing Device Units On The Controller Units Screen
Configuring the BCI-R Managing Device Units on the Controller Units Screen The BCI-R device units can be viewed and managed on the Controller Units screen from either the BACnet Setup Tool or Tracer TU. When the BCI-R first powers up, or after the controller has been cleared, a list of points (the role document) is created from the information supplied to the BCI-R from the ReliaTel RTRM module through the Modbus link.
Page 21: Leds And Switches
LEDs and Switches LEDs and Switches Table 2. Interpreting the LEDs and switches LED type LED activity Indicates... The controller is in boot mode. The controller will be placed into boot mode if the service pin is held in when power is Solid green applied.
Page 22: Additional Resources
Additional Resources Additional Resources Use the following documents and links as additional resources: • BACnet Communication Interface for ReliaTel (BCI-R) Integration Guide (BAS-SVP09) • Product support online: • www.bacnet.org • www.bacnetassociation.org • www.ashrae.org • Tracer BACnet Terminator Installation Instructions (X39641151-01) •...
Page 24 Trane - by Trane Technologies (NYSE: TT), a global climate innovator - creates comfortable, energy efficient indoor environments for commercial and residential applications. For more information, please visit trane.com or tranetechnologies.com. Trane has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.