Advertisement
Quick Links
Advertisement
Summary of Contents for Orion Tools GSN40ST
- Page 1 MODEL GSN40ST GAS CONCRETE NAILER SAFETY OPERATE MANUAL...
-
Page 2: Table Of Contents
CONTENTS ITEM PAGE 1. SAFETY ················································· 1 2. SPECI FICATION ······································· 6 3. GENERAL OPERATION MAN UAL ··············· 8 4. MAI NTENANCE ·········································· 16 5. EXPLODED DRAWI NG AND PARTS LIST··· 20... -
Page 3: Safety
SAFETY IMPORTANT INFORMATION MUST TO KNOW BEFORE TO READ IMPORTANT SAFETY I NSTRUCTIONS FOR Read and understand tool l a bels USING NAILERS and all of operating lnstrulos, READ ALL INSTRUCTIONS safaty pracaul:ions amwarnings This Nailer is powered by internal this manual before operating or combustion device. - Page 4 the Nailer, fuel Keep cells and battery 9. STORE NAILER PROPERLY WITH FUEL CELL uo• away from sunshine and from F MAI AND BATTERY REMOVED. (SO'C) temperature exceeding 120°F When not in use, the Nailer, fuel cell and battery (50"C). should be store in tool case and in a dry place.
- Page 5 17. PLACE NAILER PROPERLY ON WORKPIECE. Do not operate the Nailer when you are tired. not drive fasteners on of other fasteners The Nailer should never be used by you if you the Nailer too steep of an angle; the are under the influence alcohol, drugs or with...
- Page 6 FUEL CELL I M PORTANT SAFETY I N STRUCTIONS IMPORTANT SAFETY INSlRUCTIONS FOR BATIERY CHARGER DANGER • Fuel cell, fuel and propellant are flammable WARNING under pressure. Death or serious bodily injury could result from Explosion Fire Hazard Improper or unsafe use of battery chargers. Must to follow all instructions To avoid these risks, follow these basic safety otherwise may result in fire and...
- Page 7 Table 1 3. DO NOT short-circuit the battery. RECOMMENDED MINIMUM AWG SIZE FOR 4. DO NOT insert any objects into the battery EXTENSION CORDS FOR BATTERY CHARGERS charger's air vents. Electric shock or AC Input Ral>1Q Amperes Size of Cad damage to the battery charger may result 5.
-
Page 8: Specification
SPECIFICATION 1 GAS CONCRETE NAILER TYPE GSN40ST power Type of Piston reciprocating Applicable nails Available Nails. Nail Capacity nails Ambient temperature -5-C- 50'Cj23"Fto 120"F _l_ 420mm<l..) •378mm0-0 ><111mmtW.> Dimensions Weight 7.51bs. C3.4kg Include battery) Cycle Rate 1,...,2 nails/second BaPack NiMH 6V 1.5Ah ... - Page 9 NOTE: When fire the plastic strip nail the common concrete, should pay attention control the nail fire place with the concrete marginal range and the nail between the nail range, the distance undersize, the concrete will easy crack injure yourself or someone around you. Suggest the nail fire place with the concrete marginal range no less then 50mm, nail between the nail ranges no less than 60mm.
-
Page 10: General Operation Manual
GENERAL OPERATION MANUAL NOTE: The information contained in this Manual is designed assist you in the safe operation the Nailer. Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer. NAME OF PARTS 1.Gas Concrete Nailer ( MODEL: GSN4Dsn Top Cover Latch... - Page 11 4.Ac:ceaorla stall battery Align the battery with the groove i n tool handle It all the and s t i n to place.Always Insert untll i t l o cks in place with a little click. I f no t,i t may accidentally fall out of the tool, causing I n jury you or someone around you.
- Page 12 NOTE: The battery charging time becomes longer • If work the battery charger does not whlle the when a temperature is low or the voltage of babry Is mounlBd comic:Uy, Is probable that the power source Is low. the battery or charger malfunctlonlng.
- Page 13 •Do not spray to a naked flame or MAGAZINE ASSEMBLY INSTALL any ineandescent material. (1) Remove fuel cell and battery from naller. • •Do not smoke when handllng fuel eell. (2) Fit on the magazine assembly.Insert magazine stem away •KHp of fuel cell from into the Nail Seat.
- Page 14 Before Flashing GREEN: Enough remaining beginning the nailingwtrl, test power actually Naler by using checklst below. (The l i ght during operation). Conduct the turns steady tests Flashing RED: Insufficient power remaining order.If abnormal operation following occurs, stop using Nailer and contact a dealer (The light turns steady during operation).
- Page 15 Nail Feeding Step 1. Binding inspection lock nut is locking, ensure the snap Remove the finger from the bigger and press the that nailgroove component won't produce shaking push lever against the workpiece with pulling process (chart a). start. backward the feeder knob, motor fan Depress push lever against the Do not pull...
- Page 16 Do not ..aund axhauat touch outlet with bare hands. 4. Put the nail into the magzain, the front of the The push l e ver and nose wlll with nalls should aligned the edge magzaln become hot and get heated up (chart d) •...
- Page 17 Nall Jam Remove times, downward nailer 2-3 pulling bigger, wlll In fire process meet the nail jam malfuction,remave the nalls driven. Or use after put the nallar and fuel call Indoor minutes. it according the following steps: (1) Remove the fuel cell and the battery; This Nailer is equipped with a FULL SEQUENTIAL ACTUATION MECHANISM.
-
Page 18: Maintenance
MAINTENANCE Note When the pins are fire I n to smooth surface, Jacket, suggest use the pushing ann such as NOTE: the sheet steel; iation • The 1 ra1 contained inthis Manual is designed Whan nails are fire into the wood, suggest you in the safe maintenance of the Nailer. - Page 19 • When not in use, the Nailer, fuel cell and battery Cleaning time intervals form . .. should be stored in a warm and dry place. Opera.lion Environment " wry dirty common • Keep it out reach children. ...
- Page 20 Operator troublaahooting PROBLEM CHECK METHOD CORRECTION Check for a _a l m nails. Clear a m nails. Nailer operates, Check for proper nails. Use only recommended nails. but no nail is driven. Check for a jam. Clear a jam. Check function of nail feeder. Clean and lubricate.
- Page 21 ...
-
Page 22: Exploded Drawing And Parts List
EXPLODED DRAWING AND PARTS LIST GAS CONCRETE NAILER MODEL: GSN40 ST 2 3 4 47 48 44 45 2 3 4 2 3 4 2 3 4 2 3 4 Notes: Torque(Nm) Item Remark 1～1.2 Loctitle277 1.8～2 Loctitle277 3～3.5 Loctitle272 11 1 3.5～4 Loctitle277... - Page 23 PART LIST GSN40 ST No. Parts Name No. Parts Name Specification Plate Hex Bolt M5×10 Top Cover Protect Cover 58 Nail Seat Filter Filter Cover 59 Hex.Socket HD M5×15 Retaining Ring d0=24 Runner Gasket 61 Hex.Socket HD M5×12 Rubber Gasket 62 Pushing Head Motor Assembly 63 Hex Bolt...
Need help?
Do you have a question about the GSN40ST and is the answer not in the manual?
Questions and answers