Advertisement
ENG
VERTICAL SURFBOARD
CARRIER
RRAC095
30 min
READ ME !
Thank you for purchasing a Front Runner Vertical Surfboard Carrier .
Before you start, take a moment to familiarize yourself with this Fitting Instruction and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH.
YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE.
THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE.
IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES,
YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
RRAC095_REV_A01
1
© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
Advertisement
Table of Contents
Related Manuals for Front Runner RRAC095
Summary of Contents for Front Runner RRAC095
- Page 1 IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE.
- Page 2 GET ORGANIZED Here is what you are looking at for RRAC095 IN THE BOX IN THE BOX TOOLS NEEDED IN THE BOX Surfboard Support Brackets (1 LH & 1 RH) Vertical Surfboard Bracket Vertical Bracket Catch 10mm 10mm M8 x 25 Button Head...
- Page 3 (Item 10) closest to the side profile in Step 2.1. Place two M8 x 16 x 1.6 SS Flat Washers over the Hex Bolts and loosely fasten the brackets with two M8 Nyloc Hex Nuts (Item 8). RRAC095_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 4 M8 x 16 Hex Bolts inserted in Step 2.1. Fasten the Catch with two M8 x 16 x 1.6SS Flat Washers (Item 5) and two M8 Nyloc Hex Nuts (Item 8). Make sure that the bracket is orientated as shown. RRAC095_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 5 Board in place on the carrier bracket when used in the down position. 10MM 2.10 Finish the installation by placing a M8 Nut Cap (Item 9) over all the M8 Nyloc Nuts (Item 8). RRAC095_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 6 Vertical Surf Board Bracket. Then rest the Surfboard onto the support brackets with the bottom of the Surfboard against the Vertical Bracket 10MM and hang the Stratchits over the Surfboard. RRAC095_REV_A01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 7 Congratulations. You did it. Take a step back and admire your work! Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.
Need help?
Do you have a question about the RRAC095 and is the answer not in the manual?
Questions and answers