Second Story Home Uma Quick Start Manual

UMA UMA UMA
UMA
T O D D L E R B E D
T O D D L E R B E D
T O D D L E R B E D
T O D D L E R B E D
Step 03
One Year Limited Warranty Step 05
What You Will Need
WITH BOTH THE HEADBOARD (A) AND FOOTBOARD ( B
DEFECTIVE PARTS WILL BE REPLACED WITH A ONE YEAR PERIOD FROM DATE OF ORIGINAL PURCHASE. MISSING PARTS WILL BE C.0 S I D E P A N E L
), USE THE REMAINING 8 LARGER BOLTS (H) TO SCREW
F.0 S I D E B R A C K E T x 4
REPLACED WITHON 30 DAYS FROM THE DAY OF ORIGINAL PURCHASE. SECOND STORY HOME WARRANTS ONLY NEW UNITS PUCHA-
INTO FOUR BOTTOM HOLES ON EACH OF THE PIECES.
G.0 S U P P O R T B R A C K E T x 6
-SED IN IT'S ORIGINAL PACKAGING. THE WARRANTY DOES NOT COVER USED, SECOND HAND OR DEMOS AND IS NON-TRANSFERABLE.
LEAVE THESE BOLTS LOOSE.
H.HG0 A L L E N B O L T x 2 0
I. 0 A L L E N W R E N C H x 1
ANY DAMAGED OR DEFECTIVE PART THAT RESULTS FROM NORMAL WEAR AND TEAR, ABUSE, NEGLIGENCE, IMPROPOSER USE OR
ALTERNATION TO THE FINISH, DESIGN AND HARDWARE OF THE BED, OR THE ASSEMBLY OF THIS PRODUCT ARE NOT COVERED. THE
SPECIFIC LEGAL RIGHTS OF THIS WARRANTY MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW ANY EXCLUSION OR
F I G U R E 1
LIMITATION OF INCIDENTAL OR CONSEQUENTIL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS.
CONTACT US
Step 04
STEP 05
A. QTY1
PLEASE VISIT OUR WEBSITE AT WWW.SECONDSTORYHOME.COM THERE, YOU CAN FIND MORE PRODUCT INFORMATION,
REGISTER YOUR PRODUCT, CONTACT US OR REQUEST REPLACEMENT PARTS.
TAKE THE HEADBOARD (A) AND ALIGN THE BOLTS
TO THE SIDE BRACKET (F) THAT IS ALREADY
ATTACHED TO ONE OF THE SIDE PANELS. ONCE
PLACED INSIDE THE HOLE, PRESS DOWN TO LOCK
THE BOLT IN PLACE. DO SO UNTIL BOTH THE HEAD-
BOARD (A) AND FOOTBOARD (B) ARE ATTACHED
YOU CAN EMAIL OR WRITE
TO THE SIDE PANELS (C). ONCE ALL PIECES ARE
SUPPORT@SECONDSTORYHOME.COM
ATTACHED, BEGIN TO TIGHTEN EACH OF THE
B. QTY1
BOLTS USING THE ALLEN WRENCH (J). SECOND STORY HOME
1477 DAVRIL CIR
CORONA, CA 92880
F I G U R E 2
E. QTY3
Step 06
PLACE BOTH WOODEN STABILIZER (E) INSIDE THE STABILIZER
BRACKET TO SECURE THEM IN PLACE. LAY BOTTOM PANELS
OVER WOODEN STABILIZERS.
Step: 01
Care And Maintenance
SEE FIGURE 1
PERIODICALLY CHECK YOUR BED FOR ANY LOOSE BOLTS AND SCREWS
SET SIDE BRACKET ( F ) ON THE SIDE PANEL ( C ) AS SHOWN BELOW IN
AND TIGHTEN WHERE NEEDED. IF BED IS DAMAGED, DO NOT USE.
EXAMPLE 1. PLACE BRACKET SO THE TWO HOLES ARE AGAINST THE FABRIC.
CONTACT US FOR REPLACEMENT PARTS. SPOT CLEAN ONLY. AVOID
NEXT, PLACE THE LARGER BOLT ( H ) INTO THE TWO HOLES AND TIGHTEN
EXCESS MOISTURE.
USING ALLEN WRENCH ( I ) AS SHOWN IN EXAMPLE 2. DO NOT OVER-
TIGHTEN. REPEAT UNTIL ALL FOUR BRACKETS HAVE BEEN ATTACHED
ON BOTH THE SIDE PANEL (C).
Step: 02
x 2
SEE FIGURE 2
USE THE ALLEN BOLTS ( H ) AND LOOSELY SCREW THEM INTO THE FOUR
HOLES IN THE MIDDLE OF THE SIDE PANEL. THE SUPPORT BRACKET ( G )
WILL BE PLACED BEHIND THE WASHER. ONCE IS IS SECURED, TIGHTEN THE
SCREWS. DO NOT OVERTIGHTEN.
A.0 H E A D B O R D x 1
B.0 F O O T B O A R D x 1
C.0 S I D E P A N E L x 2
D. 0
B O T T O M P A N E L x 2
E.0
W O O D E N S T A B I L I Z E R x 3
F.0
S I D E B R A C K E T x 4
G. 0
S U P P O R T B R A C K E T x 6
wHAT YOU WILL NEED
A. H E A D B O A R D
B. F O O T B O A R D
D. B O T T O M P A N E L
E. W O O D E N S T A B I L I Z E R
H. L A R G E R B O L T
J. A L L E N W R E N C H
D. QTY2
H. QTY28
B O X C O N T E N T S
H.0
I.
F. QTY4
G. QTY6
J. QTY1
C. QTY2
BOTTOM PANELS
A L L E N B O L T x 2 8
0 A L L E N W R E N C H x 1
01 03 02 04