Advertisement
2. INTRODUCTION & SPECIFICATION
A totally dry heat, no condensation, no gas, no fumes and no smell. Reaches maximum heat output within seconds of being turned on. Highly polished
aluminium reflector for maximum heat efficiency. Adjusts horizontally through 90° while mounted. Ideal for industrial or domestic applications, IP55 rated.
Power: . . . . . . . . . . . . . . . . . . . . . . 1500W
Input supply: . . . . . . . . . . . . . . . . . . 230V 50Hz 6.3A
Dimensions (W x H x D): . . . . . . . . 480 x 125 x 125mm
mounting Bracket Stand Off: . . . . . 45mm
minimum mounting Hieght:. . . . . . . 1.8m
3. MOUNTING INSTALLATION
3.1
WALL MOUNTING (fig.1)
IMPORTANT! The following points should be noted: The heater should
always have a minimum clearance of 500mm from a ceiling and at least
1000mm from any object.
IMPORTANT! Ensure that the mounting surface is capable of supporting the
weight of the heater.
IMPORTANT! The mounting bracket must be sufficiently earthed.
3.1.1 Remove the wall mounting bracket from the heater by removing the two bolts
from either end of the bracket.
3.1.2 Before drilling ensure that there are no wires or water pipes in the area where
the heater is to be placed.
3.1.3 Use the bracket as a template, fix the metal bracket to the wall by means of
the three holes and appropriate fixings (not supplied).
3.1.4 Refit the heater back onto the bracket and secure with the two bolts.
3.1.5 Adjust the angle of heater to direct heat where required, between 45° and 90°
(see fig.1).
3.2
PARASOL MOUNTING
Ensure the heater is at least 500mm away from the canvas/material of
the parasol.
3.2.1 Bolt the supplied parasol clamp to the wall mounting bracket on the back of
the heater. Bolt to one of the outer bracket holes so the parasol bracket will be
central to the main bracket.
3.2.2 Elevate the heater up to the correct height and tighten the parasol clamp around
the parasol upright to secure in place.
IMPORTANT! Ensure all minimum distances are observed.
4. OPERATION
Note: The infrared lamp is fragile and therefore it is important that it is not subjected to any unnecessary shocks or vibration and is not moved
when it is on or until cooled down.
WARNING! Ensure you read, understand and apply the safety instructions in Section 1 before using the heater.
4.1
Ensure the heater is at least 1000mm from any object. The heater can be tilted from 45° to 90° set it to the required angle before
switching the heater on. Adjust the heater angle by loosening the two bolts on the wall mounting bracket. Tighten the bolts again when
the desired angle is reached.
4.2
Ensure that the mains supply is adequately protected and that the mounting bracket is earthed, then switch on.
4.3
make sure the heater is disconnected from the mains supply before any cleaning is attempted. Also allow the heater to cool
completely.
4.4
When the heater is no longer required, switch off and unplug the unit.
4.5
Clean the exterior with a soft damp cloth.
4.6
To replace the element, contact your authorised Sealey dealer.
4.7
The mains lead is made from high temperature cable, not a standard PVC cable and as such should not be replaced without consulting a
suitable qualified electrician.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
fig.1
01284 757500
Web
01284 703534
email
IWmH1555
www.sealey.co.uk
sales@sealey.co.uk
Issue: 2 - 15/04/10
Advertisement
