HEAT GLO FS-3-BK Installation Instructions

Firescreen decorative front

Advertisement

Models: FS-3-BK, FS-5-BK, FS-7-BK, FS-7BV-BK, FS-9-BK, FS-7-BK-AU
Leave this manual with party responsible for use
and operation.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
DANGER
DO NOT TOUCH GLASS
NEVER ALLOW CHILDREN
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and must be installed for
the protection of children and other at-risk
individuals.
WARNING! Risk of Fire! Combustible materials MUST
NOT overlap or be placed behind a decorative front.
CAUTION! Do not install damaged components.
Note: For use with the Fusion (SL-5F, SL-7F) models,
discard hood included with the FS-5-BK and FS-7-BK
and use the hood that originally shipped with the appli-
ance. Hood clips are already installed on the appliance.
1. Remove all materials from the packaging.
2. Install the black shoulder bolts into the threaded inserts
located in the fireplace surround. See Figure 1. Install
four shoulder bolts on FS-3, FS-5, FS-7, FS-7BV and
FS-9 appliances. Install two shoulder bolts on FS-7-
BK-AU front only. Do not install lower shoulder bolts
for this front. The FS-7-BK-AU front uses seperate
magnet brackets on the bottom that are included with
the appliance.
Heat & Glo • FS-3-BK, FS-5-BK, FS-7-BK, FS-7BV-BK, FS-9-BK, FS-7-BK-AU Decorative Front Instructions • 2372-931 Rev. E • 6/21
1
Firescreen Decorative Front
- Installation Instructions -
HOT GLASS WILL
CAUSE BURNS.
UNTIL COOLED.
TO TOUCH GLASS.
3. Verify that the glass assembly is centered (left to right)
within the fireplace opening.
4. Remove the two screws that fasten the hood to the
side columns of the firescreen decorative front. Set the
hood in a safe place where it will not be damaged while
the decorative front is being installed on the appliance.
Figure 1. Shoulder Bolt Locations

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FS-3-BK and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HEAT GLO FS-3-BK

  • Page 1 BK-AU front only. Do not install lower shoulder bolts for this front. The FS-7-BK-AU front uses seperate magnet brackets on the bottom that are included with the appliance. Heat & Glo • FS-3-BK, FS-5-BK, FS-7-BK, FS-7BV-BK, FS-9-BK, FS-7-BK-AU Decorative Front Instructions • 2372-931 Rev. E • 6/21...
  • Page 2 Heat & Glo, a brand of Hearth & Home Technologies not restore the original color. 7571 215th Street West, Lakeville, MN 55044 www.heatnglo.com Heat & Glo • FS-3-BK, FS-5-BK, FS-7-BK, FS-7BV-BK, FS-9-BK, FS-7-BK-AU Decorative Front Instructions • 2372-931 Rev. E • 6/21...

This manual is also suitable for:

Fs-5-bkFs-7-bkFs-7bv-bkFs-9-bkFs-7-bk-au

Table of Contents