1 ABOUT 1.1 Manual Description Dear users, thanks a lot for using the HG-SB01 produced by HOMEGRID. We sincerely hope that this product can meet your needs. The purpose of this manual is to provide users with detailed product information and installation, operation and maintenance instructions.
Page 6
1.4 Use Manual Please read this manual carefully before using the HG-SB01. At the same time, please keep this manual properly for easily reach of the operation and maintenance personnel. The contents of the manual will be constantly updated and corrected, and it is inevitable that there are slight discrepan- cies or errors with the real object.
Figure 2.1.1 HG-SB01 Interface Definition Instractions Can/RS485 communication upgrade port RS232 communication upgrade port 2.1.2 State Indicator Light The status of the HG-SB01 can be indicated from the LED indicators according to the following table. Status Light Description The power indicator is always on, which means that the Red Light power supply is normal.
2.1.3 Button Button function descriotion: Reserved 2.2 Unpack Packaging The main accessories of the HG-SB01 are as follows: Instractions Quantity HG-SB01 Wi-Fi antenna HG-SB01 RS232 communication cable HG-SB01 RS485 communication cable HG-SB01 CAN/RS485 upgrade cable 3 OPERATION AND APPLICATION 3.1 System Principle Block Diagram CAN/RS485 Wi-Fi Upgrade line...
Page 10
3.2 HG-SB01 Operation 3.2.1 Connect to Wi-Fi 1. Open the Skybox Wi-Fi config tool folder; 2. Double click to run the Skybox application; 3. Connect the computer to the hotspot of Skybox (HG-EMS-***). Enter the password: 12345678, and click Connect; HG-EMS-F27E Connecting Enter the network security Key...
Page 11
5. Click “Set”, the software will prompt whether the configuration is successful. Description: This software is sed to configure Skybox to connect to the specific Wi-Fi Operation Steps: 1. Connect the computer to the hotspot of Skybox(HG-EMS-***). 2. Fill in the SSID and password to the Wi-Fi to which the Skybox will be connected into the SSID and Password box in the software 3.
Page 12
to the HG-SB01 firmware upgrade screen. 2. Click Select File to find the file you want to update, select it, and open it. The current firmware version is displayed in the upper right corner of the page.
Page 13
3. Select the device that you want to update and click Update. The upgrade progress is displayed in the status bar. When the upgrade progress reaches 100%, the upgrade is complete. This manual indicates the procedure of remote upgrade via Web Server, Mobile APP will be coming soon.
Page 14
3.2.4 Local Upgrade 1. Take out the accessory power supply line and connect it to Hall current port on the controller to supply power to HG-SB01 Dry Contact +12VIN -12VIN Hall Current POWER...
Page 15
Note: The 5-PIN controller port of the old version does not match the current main control port. The HG-SB01 power terminal needs to be replaced as follows: Connect the +12V power terminal to the 5-pin port and the -12V power terminal to the 3-pin port defined in the figure.
Page 16
Link-B Link-A RS485 RS232 Note: During the upgrade process, HG-SB01 needs to maintain the power supply, and the communication cannot be interrupted, otherwise the upgrade will lose power and crash, which may lead to the death of the device.
Page 17
3. After the connection is successful, the system will be automatically upgraded. After the connection is complete, the Skybox will compare the existing firmware version with the latest version. If the upgrade is needed, you will hear the buzzer from Skybox beeps once and the blue indicator blinks rapidly, this means that the upgrade is in progress.
Page 18
Link-B Link-A CAN/RS485 RS232 RS485 RS232 Adress Note: During the upgrade process, HG-SB01 needs to maintain the power supply, and the communication cannot be interrupted, otherwise the upgrade will lose power and crash, which may lead to the death of the device.
4 COMMON FAULTS Fault Description Sympton of Faulty Equipment Solutions 1. Ensure that the router network works properly The WIFI connection has 2. Ensure that the been offline for a long The green indicator is off for a long time working frequency band time of the network signal is...