Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for M&C Universal Filter FT H2 Series
- Page 1 ® Universal Filter Series FT FT-...-H2 Instruction Manual Version 1.00.01...
- Page 2 Dear customer, we have made up this operating manual in such a way that all necessary information about the product can be found and understood quickly and easily. Should you still have any question, please do not hesitate to contact M&C directly or go through your appointed dealer.
-
Page 3: Table Of Contents
Contents General information ........................4 Declaration of conformity ......................4 Safety instructions ........................5 Warranty ............................5 Used terms and signal indications .................... 6 Introduction and application ...................... 7 Serial numbers ........................7 Power supply ......................... 7 Warnings and instructions...................... 7 Technical Data .......................... -
Page 4: General Information
Head Office M&C TechGroup Germany GmbH Rehhecke 79 40885 Ratingen Germany Telephone: 02102 / 935 - 0 Fax: 02102 / 935 - 111 E - mail: info@mc-techgroup.com www.mc-techgroup.com GENERAL INFORMATION The product described in this operating manual has been examined before delivery and left our works in perfect condition related to safety regulations. -
Page 5: Safety Instructions
SAFETY INSTRUCTIONS Please take care of the following basic safety procedures when mounting, starting up or operating this equipment: Read this operating manual before starting up and use of the equipment. The information and warnings given in this operating manual must be heeded. Any work on electrical equipment is only to be carried out by trained specialists as per the regulations currently in force. -
Page 6: Used Terms And Signal Indications
USED TERMS AND SIGNAL INDICATIONS This means that death, severe physical injuries and/or important material damages will occur in case the respective safety measures are not fulfilled. D AN G E R ! This means that death, severe physical injuries and/or important material damages may occur in case the respective safety measures are not fulfilled. -
Page 7: Introduction And Application
INTRODUCTION AND APPLICATION The M&C electrically heated universal filter FT-…-H2 reliably separates off solids, in particular extremely fine particles, occurring in analysis techniques in gas filtration, using very fine, deep-acting filter elements. It is constructed especially for hot gas analysis technique at 180°C. SERIAL NUMBERS The nameplates bearing the serial number are located on the mounting plate. -
Page 8: Technical Data
TECHNICAL DATA ® Filter series FT FT-3G-H2 FT-3SS-H2 FT-0,1GF-H2 Part number 01 F 3006(a) 01 F 3008(a) 01 F 3007(a) Filter finess/material of filter element 3µm / glass 3µm / stainl. steel 0,1µm / glassfibre Power supply 230 - 240V 50Hz, 350VA or 115V 60Hz (a) Electrical connection 2,5mm terminals, 2x PG13 cable glands... -
Page 9: Description
DESCRIPTION The universal-filter out of PTFE with integrated filter elements (fineness 3 or 0,1 µm) is placed in an electrically heated 2-part aluminium construction. The temperature is controlled by an integrated compact capillary sensor thermostat with an excess temperature limit switch with reset key at +30°C above T and an alarm function for low temperature alarm at -30°C below T with voltage free status-alarm contact. -
Page 10: Reception And Storage
RECEPTION AND STORAGE The universal filter series FT-…-H2 is normally delivered in one packaging unit: The universal filter series FT-…-H2 should be removed carefully from the packaging and checked immediately for completeness against the delivery note. Check the goods for any damage incurred during transport and if necessary inform your transport insurer of any damage. -
Page 11: Electrical Connection
ELECTRICAL CONNECTION When connecting the equipment, please ensure that the supply voltage is identical with the information provided on the model type plate. W A R N I N G ! After mounting the filter, the posssibility of getting in touch with live parts has to be prevented! The use of temperature resistant cable is necessary ! Attention must be paid to the requirements of IEC 364 (DIN VDE... -
Page 12: Figure 2 Electrical Connecting Diagram
Figure 2 Electrical connecting diagram FT-…-H2 | 1.00.01 www.mc-techgroup.com... -
Page 13: Starting
STARTING Before using the equipment for the first time, check that the safety measures specific to the installation and process are complied with! For the carried media the corresponding safety regulations and measures have to be considered. Before starting up check whether the mains power supply voltage corresponds with the information stated on the nameplate. -
Page 14: Maintenance
MAINTENANCE The safety instructions specific to the plant and process are to be consulted prior to any maintenance work! Aggressive condensate is possible. W A R N I N G ! Wear protective glasses and proper protective clothing! High surface temperatures! Touching the filter surface can cause serious burns! Wear protective gloves and protect the filter of unauthorized access! -
Page 15: Spare Parts List
SPARE PARTS LIST Wear, tear and replacement part requirements depend on specific operating conditions. The recommended quantities are based on experience and they are not binding. Recommended quantity ® Universal filter series FT -..-H2 For operating period (C) Consumables, (R) recommended spare parts, and [years] (S) spare parts V/E/T...