Advertisement
TFP ELIMINATOR
Installation & Operating Instructions for
ME500XF, ME500XC, ME800XF, ME800XC, ME1400XF, ME1400XC, ME1400XCM,
ME2000XC, ME2000XF, ME2500XCR, ME2500XFR, ME4000XF, ME4000XC, ME6000XF,
ME6000XC
Features
High efficiency collection for wet mist
Low power consumption
motors available in various voltages
Durable epoxy powder paint
Low maintenance
Easy to change collectors
Compact design
rd
Optional 3
stage filters
Applications
Machining centers
Boring mills
Screw Machines
Die casting machines
High speed grinders
Mounting
1. The TFP ELIMINATOR can be suspended from above, attached directly to the top of
the machine or bolted to a support frame. Make sure that the support has adequate
strength. For congested areas, purchase the column mount which will fit into a small
floor space and will place the TFP-ELIMINATOR 7 feet above the floor.
2. To provide access for maintenance, a minimum clearance of 30" (77cm) is required
above the ME500XF, ME800XF, ME1400XF, ME1400XCM, ME2000XF, ME2500XFR,
and ME2500XCR. The minimum clearance above the ME4000XF and ME6000XF is
50" (127 cm).
3. When suspending the smaller units ME500, ME800, ME1400, ME2000XF and
ME2500XC and ME2500XF series units, use the four mounting holes at each top
corner. A chain or cable can be attached to these holes to suspend the unit from
overhead steelwork. When mounting on a support frame, bolt to the frame using the
four holes at the bottom of the ME500XF, ME800XF, ME1400XF, ME2000XF,
ME2500XC and ME2500XF series units and the eight holes at the bottom of the
ME4000XF and ME6000XF units.
1 of 10
TFPS V8
12/03/09
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Airia ME500XF
- Page 1 A chain or cable can be attached to these holes to suspend the unit from overhead steelwork. When mounting on a support frame, bolt to the frame using the four holes at the bottom of the ME500XF, ME800XF, ME1400XF, ME2000XF, ME2500XC and ME2500XF series units and the eight holes at the bottom of the ME4000XF and ME6000XF units.
- Page 2 4. Check to make sure that the unit is level. Attach the collection duct to the inlet end of the TFP ELIMINATOR. When installing with parts washers refer to section 10 for additional requirements Connect liquid traps/drainage tubes to the drains on the bottom of the unit. For proper operation traps must be incorporated into the drainage system.
-
Page 3: Preventative Maintenance
Adjusting the Damper to Control the Mist from Parts Washer 1. To find the proper damper setting, start the parts washer 2. Let it achieve normal operating temperature 3. Then, beginning with the damper in the wide open position, close it gradually until the mist ceases to escape from the parts washer and lock in that position. - Page 4 Gaskets Check the gaskets for tears, deformation and sagging. Re-attach sagging gaskets. Please Airia Inc. note that if replacement gaskets are needed, they are only available from your Nutech Inc. supplier. The door gaskets are clipped on while the filter stop gaskets are glued onto the frame with Permabond 102.
-
Page 5: Troubleshooting
Installation & Replacement of TFP Cartridge or Optional 3 Stage Filter Disconnect power to unit and follow your lock-out procedure. Be sure to wear protective gloves when working on the unit. To replace cartridge or filter, undo the latches and remove the top cover. Release the clamps holding the cartridge(s) and/or filter(s) in place. - Page 6 This drain does not require a trap. DO NOT connect to other drain. Fill trap before starting unit. Fill trap before starting unit . Models ME500XC, ME500XF 12” 8” 4” 3” ME800XC, ME800XF 14” 12” 4” 3” ME1400XC, ME1400XCM, ME1400XF 14”...
-
Page 7: Specifications
Specifications ME 500XF ME 800XF ME 1400XF ME 2000XF ME 2500XF FLOW CAPACITY 500 CFM 800 CFM 1400 CFM 2000 CFM 2500 CFM LENGTH 59" ( 150 cm) 65" (165 cm) 65.375" (166 cm) 75" (190 cm) 77" (196 cm) HEIGHT 24"... -
Page 8: Replacement Part Numbers
Specifications ME4000XF ME6000XF FLOW CAPACITY 4000 CFM 6000 CFM LENGTH 86-1/2” (220 cm) 93” (236 cm) HEIGHT 26-3/4” (68 cm) 27-5/8” (70 cm) WIDTH 48-1/4” (123 cm) 67” (170 cm) INLET 18” (46 cm) 24” (315 cm) MOTOR 10 H.P. 15 H.P. - Page 9 Replacement Part Numbers ME 2000XF ME2000XC ME 2500XCR/XFR ME 2500XCS/XFS Door Seal 13-112 13-112 13-112 13-112 Partition Seal 13-137 13-137 13-137 13-137 Impeller 40-109 40-109 40-125 40-23 Venturi Ring 40-111 40-111 40-112 40-124 Blower Grille 61-2501-13 61-2501-13 61-2501-13 61-2501-13 Door Latch 91-108 91-108 91-108...
- Page 10 NUTECH, are excluded from this warranty. If you feel that the TFP-Eliminator you purchased is not free from manufacturing defects, please contact Airia Group of Company's Inc. NUTECH ENERGY SYSTEMS INC., 511 McCormick Blvd., London, Ontario N5W 4C8, 519-457-1904 or fax 519-457-1676.
Need help?
Do you have a question about the ME500XF and is the answer not in the manual?
Questions and answers