1. Manuals
  2. Brands
  3. Toto Link Manuals
  4. Network Hardware
  5. CP300L
  6. User manual

Toto Link CP300L User Manual

Wireless outdoor cpe
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Guide
2
PCS
Set
Wireless Outdoor CPE
CP300L / CP900L

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CP300L and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Toto Link CP300L

  • Page 1 User Guide Wireless Outdoor CPE CP300L / CP900L...

  • Page 2: Table Of Contents

    Content Introduction 1. Package Contents 2. LED Indicators 3. Interface 4. Passive PoE Box Hardware Installation 1. Connection and Installation Software Installation 1. Preparation 2. PC Settings 3. Web Interface Login CPE 4. Application Scenario (Auto bridge)

  • Page 3: Introduction

    Introduction 1. Package Contents CPE *2 PoE Box *2 Ethernet Cable *2 Strip *4 User Guide *1 Power Adapter *2 2. LED Indicators -80dBm -70dBm LAN1 LAN2 Signal Strength LED Status Description CPE is working on AP Mode(Master Device). CPE is working on Client Mode(Satellite Signal Strength Device)/Repeater Mode/WISP Mode.

  • Page 4: Interface

    3. Interface (12V Passive PoE) RESET LAN2 LAN1 DC IN Cable Ties Holes Wall Mounting Holes Interface Description RJ45 port, also used as PoE port，can simultaneously LAN1/LAN2(PoE IN) transmit data and power the device. DC IN Power port, connect the included power adapter. RESET Press and hold for more than 8 seconds until the signal strength LED quickly blinking, the system will reset.

  • Page 5: Passive Poe Box

    4. Passive PoE Box PoE box PoE box Front Back Interface Description This RJ45 port is used to connect PC for data input. DC IN Power port, connect the included power adapter. POWER Power indicator, it is lighting when power on. This RJ45 port is used to connect TOTOLINK CPE for data and power transfer.

  • Page 6: Connection And Installation

    Connection and Installation: Switch Wall socket PoE box Step 2. After the Ethernet cable connection, push up the sliding closure to make it fasten again on the case.

  • Page 7: Software Installation

    Step 3. Fix the CPE to the pole by strips, then adjust it to face the Wi-Fi coverage area. Software Installation 1.Preparation Here we take TOTOLINK CP900L (CPE-1 and CPE-2) as an example to instruct how to configure CPE. Master CPE: CPE-1 ，SSID is TOTLINK_XXXXXX (XXXXXX is the last six digits of the MAC address on the sticker).

  • Page 8: Pc Settings

    2.PC Settings After hardware connection, please setup the network parameters of your PC (1) Click “Start—Control Panel—Network and Sharing Center—Change adapter setting ”, right-click “Ethernet ”, and choose “Properties”. (2) Double-click “Internet Protocol Version 4 (TCP/IPv4)”.

  • Page 9: Web Interface Login Cpe

    (3) Choose “Use the following IP address”, set the lP address to 169.254.0.X (X ranges from 2 to253), the Subnet mask to 255.255.255.0, and click “OK ”. 169 . 254 . 0 3.Web Interface Login CPE Two CPEs in the pack have been paired successfully as the factory default setting. Users could pair them manually when replacing the pairing CPE.
  • Page 10 ① Open Web browser and visit 169.254.0.254. Enter the password admin and click Login. ② Click “Operation Mode ” in the coming setup page. ③ Choose a suitable working mode in the Operation Mode page according to the local scenario and then click “SCAN ”. The CPE will search the surrounding wireless Network automatically.

  • Page 11: Application Scenario (Auto Bridge)

    4. Application Scenario (Auto bridge) Install CPE to the appropriate location as needed. Please refer to the body sticker instructions for the master and satellite devices. This guide takes the pole-holding installation as an example. When installing, put the tie through the tie hole on the back of the CPE, and put the CPE close to the pole, adjust the position and orientation of the CPE according to the signal indicator, and pull the tie to secure it.
  • Page 12 Outdoor area monitoring diagram Satellite CPE Master CPE Router Internet Switch Switch Elevator monitoring Master CPE-1 Satellite CPE-1 Satellite CPE-2 Master CPE-2...

  • Page 13: Faq

    How to reset the CPE to factory default Settings? Keep the CPE powered on, press the RESET button on CPE about 8 seconds, the CPE will restore to factory default settings. RESET： Press and hold for more than 8 seconds until the signal strength LED quickly blinking, the system will reset.
  • Page 14 ♦ Copyright ⓒ by TOTOLINK. All rights reserved No company or individual may copy or reproduce part or all of the contents of this document without the written permission of the Company, and may not transmit it in any form. ♦...

This manual is also suitable for:

Cp900l

Table of Contents