Wireless Charging - Vector VECLIPS4 Instruction Manual

SOLAR PANEL CHARGING
• Place the solar panel in direct sunlight
• Connect the charging cable, charging will start automatically.
• The Indicator will show you the charging battery level and "Time to Full"
on the remaining charge time.
• When fully charged, remove the cable from the unit.
Note. Use only 200 Watt max solar panel with a regulated voltage
between 11-30 VDC. Solar panel is not included and sold separately
SPECIFIC SAFETY INSTRUCTIONS FOR
INVERTERS
WARNING –
To reduce the risk of electric shock:
• Do not connect to AC distribution wiring.
• Do not make any electrical connections or disconnections in areas
designated as IGNITION PROTECTED. This inverter is NOT approved for
ignition protected areas.
• Never immerse the unit in water or any other liquid, or use when wet.
WARNING –
To reduce the risk of fire:
• Do not operate near flammable materials, fumes or gases.
• Do not expose to extreme heat or flames.
CAUTION –
To reduce the risk of injury or property damage:
• Disconnect appliance plug from inverter outlet before attempting any
repairs to the appliance.
• When an appliance plugged into this unit is used outdoors, use only
extension cords intended for use outdoors and so marked.
• Do not attempt to connect the inverter while operating your vehicle. Not
paying attention to the road may result in a serious accident.
• Always use the inverter where there is adequate ventilation.
• Always turn the inverter off when not in use.
• Keep in mind that this inverter will not operate high wattage appliances
or equipment that produce heat, such as hair dryers, microwave ovens
and toasters.
• Do not use this inverter with medical devices. It is not tested for medical
applications.
• Operate inverter only as described in this Instruction Manual.
120 VOLT AC PORTABLE POWER SUPPLY
The unit is equipped with a 500W pure sine wave inverter to provide
power for all suited electronic equipment and electrical appliances.
However, you need to confirm the power rating and socket type of the
device to be used. The AC rated output power of this unit is not more
than 500W. Devices such as fans or electric motors require additional
power to start (commonly known as the "starting" or "peak" power). The
generator can supply a momentary surge in wattage of as high as 1000W
for less than 1/10 of a second; however even devices rated less than the
maximum 500W can exceed the inverter's surge capability and cause an
overload automatic shutdown.
Do not use products with more power than the inverter can provide, as
this can lead to a risk of instability.
In the event of power overload (with a flashing warning symbol on the
LCD screen), the AC output will automatically turn off, a safety feature that
prevents the device from damaging the inverter.
If powering more than one device, start one device at a time to avoid
power surges and/or inverter overloads. The surge load of each device
shall not exceed the inverter's rated power. You can use an extension cord
from the inverter to the device without significantly decreasing the power
being generated by the inverter. For best operating results, the extension
cord should be 16 AWG (1.31 mm ) or larger and no longer than 50 feet.
• Connect your AC power supply device or small household appliance to
one or more of the unit's two AC output sockets (make sure the device to
be supplied is turned off before inserting the plug into the AC socket).
• Make sure the main power is on, then press the AC button to turn on the
AC output, and the corresponding symbol will be displayed on the LCD
screen.
• After use, press the AC button again, turn off the AC output of the unit,
and pull out the device plug from the AC output socket of the unit.
SPECIFIC SAFETY INSTRUCTIONS FOR THE
USB-A & USB-C PORTS
• Do not insert foreign objects into the USB Port.
• Do not attach USB hubs or more than one personal electronic device to
the USB Port.
• Some household USB-powered electronics will not operate with this unit.
USB-A & USB-C CHARGING PORTS
Insert the input end of the device cable into the USB-A port or type-C port
of the unit. First make sure that the main power is on. Then press the USB
button on the control panel to turn on the output, and the corresponding
symbol will be displayed on the LCD screen.
After charging is completed, press the USB button again to turn off the
output of the unit, and pull the wiring plug from the USB-A or Type-C
output port of the machine.
The USB power port remains on until the USB power button is pressed
again to turn it off. Make sure the USB port is turned off when the unit is
being recharged or stored.
Periodically check the unit's Battery Status on the backlit LCD screen.
Note:
This unit's USB power port does not support data communication.
Note:
The USB-C symbol only appears on the LCD screen when the device cable is
inserted in the 60W PD port.

WIRELESS CHARGING

The built-in Wireless Charging feature is suitable for most appliances with
a Wireless Charging function.
Before proceeding, check the unit's battery status on the LCD screen.
When the battery level is nearly empty with only one solid bar, the unit
MUST be recharged before use or the unit's built-in low voltage protection
will activate. The empty Battery Status Icon will flash for a short period of
time before automatic shut down.
WIRELESS OUTPUT
Press wireless button to activate standby mode.
Flashes slowly
Solid during charging
Quick flashing when a fault is detected
IMPORTANT:
• Make sure the Wireless Charging function is turned off when the unit is being recharged
or stored.
• Note: Wireless charging may not work with some devices that are not Qi-certified. Wireless
charging is available with some compatible Qi-certified devices up to 10W. For other
devices, slower charging rates will apply. Actual charging speed may vary depending on
multiple factors such as battery condition and frequency of use.
7