Download
Share
Print this page
  1. Manuals
  2. Brands
  3. JICCODA Manuals
  4. Printer
  5. LE-1
  6. Quick install manual

JICCODA LE-1 Quick Install Manual

Laser engraving machine
Hide thumbs

Advertisement

Quick Links

QUICK INSTALL GUIDE
LE-1
Laser Engraving Machine
10

Advertisement

loading

Summary of Contents for JICCODA LE-1

  • Page 1 QUICK INSTALL GUIDE LE-1 Laser Engraving Machine...

  • Page 2: Table Of Contents

    Contents • Package list check ------------------------------------------------------------------------------------------------------------2 • Set up LE-1------------------------------------------------------------------------------------------------------------------------4 • Download and install software -------------------------------------------------------------------------------------------34 • Safety guidelines---------------------------------------------------------------------------------------------------------------42 • One year warranty-------------------------------------------------------------------------------------------------------------43...

  • Page 3: Package List Check

    PT.1 Package list check Rear rail *1 Y Endstop *1 Tensioner Assembly *1 X Rail *1 Right Side Rail *1 Left Side Rail *1 Front rail *1 Laser Module *1 Control Board *1 X Sliding Assembly *1 X Endstop *1 L-angle bracket *4 L Motor assembly *1 R Motor assembly *1...
  • Page 4 PT.1 Package list check X Synchronous Belts *1 24V Adapters *1 Power cable *1 Y Synchronous Belts *2 M3x6 Screws *14 M5x18 Screws *5 M3x8 Screws *7 Protective glasses *1 USB cable *1 M5x8 Screws * 6 M5x20 Screws * 11 M5x25 Screws *1 Measuring tools *1 Tool Kit *1 M5x55 Screw *1...

  • Page 5: Set Up

    PT.2 set up LE-1 Step 1 Parts Required: • M3x6 Screws *2 • Drag chain bracket *1 • R Motor assembly *1 Align the holes as shown and secure with M3x6 screws. Drag chain bracket *1...
  • Page 6 PT.2 set up LE-1 Step 2 Parts Required: • Right Side Rail *1 • Assembly (Step 1) *1 Identify the Right Side Rail by the scale on the surface and the orientation of the hole. Slide the Assembly (Step 1) assembly into the Right Side Rail, following the direction of the arrow in the diagram.
  • Page 7 PT.2 set up LE-1 Step 2 Parts Required: • Assembly (Step 2) *1 If the assembly is very loose in the Rail, use a hexagonal spanner to adjust the rollers as shown by the arrows in the picture. Notes： 1. The same set of rollers are adjusted at the same time.
  • Page 8 PT.2 set up LE-1 Step 3 Parts Required: • Assembly (Step 2) *1 • Y Synchronous Belts *1 • Belt Screws *2 3.1 Belt screw slides in through the guide slot (in the direction of the arrow) 3.2 The belt is placed under the belt screw and the screw is tightened 3.3 Belt wraps around the gear on the motor (as...
  • Page 9 PT.2 set up LE-1 Step 4 Parts Required: • Assembly (Step 3) *1 • Y Endstop *1 • M5x20 Screws *1 Note the direction of installation Stick flat on the bottom of the rail and fix with M5x20 screws.
  • Page 10 PT.2 set up LE-1 Step 5 Parts Required: • Left Side Rail *1 • L Motor assembly *1 Identify the Right Side Rail by the scale on the surface and the orientation of the hole. Slide the L Motor assembly into the Right Side Rail, following the direction of the arrow in the diagram.
  • Page 11 PT.2 set up LE-1 Step 5 Parts Required: • Assembly (Step 5) *1 If the assembly is very loose in the Rail, use a hexagonal spanner to adjust the rollers as shown by the arrows in the picture. Notes： 1. The same set of rollers are adjusted at the same time.
  • Page 12 PT.2 set up LE-1 Step 6 Parts Required: • Assembly (Step 5) *1 • Y Synchronous Belts *1 • Belt Screws *2 3.1 Belt screw slides in through the guide slot (in the direction of the arrow) 3.2 The belt is placed under the belt screw and the screw is tightened 3.3 Belt wraps around the gear on the...
  • Page 13 PT.2 set up LE-1 Step 7 Parts Required: • Assembly (Step 4) *1 • Assembly (Step 6) *1 • Front rail *1 • Rear rail *1 • M5x20 Screws *6 Place according to the scale markings (as indicated by the arrows in the picture)
  • Page 14 PT.2 set up LE-1 Step 8 Parts Required: • Assembly (Step 7) *1 • Frame Foot *3 • M5x8 Screws *3 • M5x20 Screws *3 The screws for fixing to the left and right rails are M5x8 The screws fixing the front and rear rails are...
  • Page 15 PT.2 set up LE-1 Step 9 Parts Required: • Assembly (Step 8) *1 • Control Board *1 • M5x8 Screws *1 • M5x20 Screws *1 The screw fixed to the right rail is M5x8 The screw fixed to the front rail is M5x20...
  • Page 16 PT.2 set up LE-1 Step 10 Parts Required: • X Sliding Assembly *1 • X Drag Chain Bracket *1 • M3x6 Screws *3 X Drag Chain Bracket attached to X Sliding Assembly Fix with M3x6 screws (as shown in the picture)
  • Page 17 PT.2 set up LE-1 Step 11 Parts Required: • Assembly (Step 10) *1 • X Rail *1 The motor cable goes through first, otherwise it will prevent the assembly from sliding in Assembly (Step 10) slides into the X Rail (as...
  • Page 18 PT.2 set up LE-1 Step 11 Parts Required: • Assembly (Step 11) *1 If the assembly is very loose in the Rail, use a hexagonal spanner to adjust the rollers as shown by the arrows in the picture. Notes： Optimum looseness: the POM wheels rub slightly against the guide rails as they turn.
  • Page 19 PT.2 set up LE-1 Step 12 Parts Required: • Assembly (Step 11) *1 • White Nylon Tubes 25 *2 • M5x55 Screw *1 White Nylon Tubes 25 length 2pcs stacked on the assembly with M5x55 screws (as shown)
  • Page 20 PT.2 set up LE-1 Step 13 Parts Required: • Assembly (Step 9) *1 • Assembly (Step 11) *1 • M5x18 Screws *4 Motor wires avoiding L motor assembly and R motor assembly (as shown in the picture) Use M5x18 screws 4PCS to secure the L motor assembly and R motor assembly, do not tighten them yet.
  • Page 21 PT.2 set up LE-1 Step 14 Parts Required: • Assembly (Step 13) *1 • X Endstop *1 • M5x25 Screws *1 X Enstop attached to the left end of the X-rail, Fixed with M5x25 screws...
  • Page 22 PT.2 set up LE-1 Step 15 Parts Required: • Assembly (Step 14) *1 • M5x18 Screw *1 Through the hole in the L motor assembly Use M5x18 screws to fix the L motor assembly and X Rail Plug the 6pin connector into the motor on the L...
  • Page 23 PT.2 set up LE-1 Step 16 Parts Required: • Assembly (Step 14) *1 • Tensioner Assembly *1 T Nut Before use, loosen the screws on the Tensioner Assembly so that the T-nut can just hold the X Rail guide. If it does not fit into the slot, loosen the screw...
  • Page 24 PT.2 set up LE-1 Step 16 Parts Required: • Assembly (Step 15) *1 • X Synchronous Belts *1 One end of the X Synchronous Belts snaps into the slot on the X Sliding Assembly (as shown) Place the timing belt in the order of 1 to 5 Finally, snap the other end of the timing belt into the X Sliding Assembly slot (see Fig.
  • Page 25 PT.2 set up LE-1 Step 17 Parts Required: • Assembly (Step 16) *1 When rotating clockwise, tension the timing belt When rotating counterclockwise, loosen the timing belt The timing belt needs only a little tension Do not over tighten.
  • Page 26 PT.2 set up LE-1 Step 18 Parts Required: • Assembly (Step 17) *1 • M3x6 Screws *6 One end of the drag chain is attached to the control board sub bracket and then fixed with screws M3x6 The other end of the drag chain is attached to...
  • Page 27 PT.2 set up LE-1 Step 19 Parts Required: • Assembly (Step 17) *1 • M3x6 Screws *3 • M3x8 Screws *3 One end of the drag chain is attached to the bracket of the R-motor assembly and fixed with screws M3x8...
  • Page 28 PT.2 set up LE-1 Step 20 Parts Required: • Assembly (Step 19) *1 • Y Drag Chain Support *1 • M5x8 Screws *2 Y Drag Chain Support is attached to the Bottom of the R-motor assembly and fixed with screws M5x8 The first hole on Y Drag Chain Support is not used（Near the bending edge）...
  • Page 29 PT.2 set up LE-1 Step 21 Parts Required: • Assembly (Step 20) *1 The air supply hose is inserted into this regulating valve (as shown) How to change the airflow When rotating clockwise, the airflow becomes smaller When rotating counterclockwise, the airflow becomes...
  • Page 30 PT.2 set up LE-1 Step 22 How to connect the wires Y2 Motor Y1 Motor X Motor Y Endstop Y2 Motor...
  • Page 31 PT.2 set up LE-1 Step 22 How to connect the wires Flame monitoring X Endstop Laser...
  • Page 32 PT.2 set up LE-1 Step 23 Introduction to the control board Power switch How to enable the machine：  DC power socket connected to DC 24V power supply  Press the power switch Emergency stop  Turn the emergency stop switch clockwise and let it pop up ...
  • Page 33 PT.2 set up LE-1 Step 24 Knob How to position the focus  The engraved object is placed under the laser module  The bottom of the measuring tool is in Measuring tools contact with the surface of the engraving...
  • Page 34 PT.2 set up LE-1 Step 25 How to fix to a table Parts Required: • L-angle bracket *4 • M4x8 Screws *8 4 feet...

  • Page 35: Download And Install Software

    PT.3 Download and install software Driver installation Method 1. Click the "Tools" on menu bar to install the CH340 driver (this function is not available in some versions of the software); Method 2. Copy file of "CH340SER.EXE" from TF card (USB flash disk) to computer and install; Note: if it is a MAC system, install the corresponding driver, and there is a Mac driver in the TF Card;...
  • Page 36 PT.3 Download and install software Software Downloading LaserGRBL is one of the most popular DIY laser engraving software, which can be downloaded in LaserGRBL website http://lasergrbl.com/download/(The installation package is also available on the TF card from the manufacturer or USB flash disk).
  • Page 37 PT.3 Download and install software 2. Installation Package for Custom Button We recommended LaserGRBL using custom button,and can get it from our TF card. 2.1 How to down load Custom Button software Step 1: Click the blank space of the bottom (as shown in figure 3.2) Step 2: choose “...
  • Page 38 PT.3 Download and install software 3. Connect Laser Engraving Machine Step 1: Using USB data cable to connect the laser engraver to a computer with LaserGRBL software installed Step 2: turn on the laser engraving machine. Step 3: turn on the LaserGRBL software in the computer. Step 4: Select the correct port number and baud rate in the software - 115200（figure 4.4）...
  • Page 39 PT.3 Download and install software 4. UpLoad Engraving File click and select Step1:Click "file" and "open file" in turn, as shown the file of graph in figure 8.1, and then select the graph you want to engrave. Currently, LaserGRBL supports files in the formats of NC, BMP, JPG, PNG, DXF, etc.
  • Page 40 PT.3 Download and install software Step3: Set engraving speed, energy and size. The JICCODA LE-1 laser engraver can reach a speed of up to 10,000mm/min. You can of course The default engraving speed is 1000 and can be adjusted increase or decrease this speed according to your as required preference.
  • Page 41 PT.3 Download and install software 5.Position (set the origin) The purpose of positioning: the engraving pattern to be carved in the correct position of the object to be engraved. Step1: By clicking on the orientation button (Figure 6.1), moving the X/Y axis, the laser device is positioned to the appropriate Figure 6.1 position of the object to be engraved.
  • Page 42 PT.3 Download and install software 6、 Start, stop, run, pause, power and speed adjustment pause Start operating: Click the triangle green button of "Run Program" in GRBL software to start (figure 7.1). The G code produced by GRBL will be continuously transmitted to the control board of the engraving click to enter the machine.

  • Page 43: Safety Guidelines

    PT.4 Safety guidelines Safety instructions while using the laser engraver : It is strictly forbidden to place any living objects under the laser emitting port. Patients with photosensitive epilepsy are prohibited from using or approaching this laser device. When using a laser engraving machine, anyone who approaches the machine must wear laser safety goggles. Plus, our machine comes with a pair of safety goggles, but they can also be purchased on Amazon.

  • Page 44: One Year Warranty

    PT.5 One year warranty Dear Customers: Thank you for purchasing our JICCODA LE-1 laser engraver. We valued all our consumers feedback and sincerely hope you will have a nice journey with the product. JICCODA LE-1 attaches great importance to product quality and practicality, combining all laser supply chains to provide you with higher standards of quality and affordable products,which is ready to give you the best laser engraving &...
  • Page 45 LE-1 Laser Engraver...
  • Page 46 FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation.