Advertisement
Quick Links
Advertisement
Summary of Contents for HL HL-1060L
- Page 1 Laser Engrave Machine HL-1060L 100W Manual...
- Page 5 www.hl-yeah.com...
- Page 6 Section II. Uncrating HL-100W 1060L Uncrating HL-100W 1060L Crate size is on the right. That needs to lift it from one side and pull out this machine. Machine size on the left Machine front...
- Page 7 Machine back Machine control unit Parts & Accessories...
-
Page 8: Section Iii. Installation & Assembly
Section III. Installation & Assembly 1. Connect the Exhaust(Optional part, buy separately) - Page 9 2. Connect the Water Chiller& Air Compressor CO2 Laser machines use water cooling laser tubes. Laser technology is such that the laser tubes generate a lot of excess heat and the tubes must be cooled for proper operation. Equipment running environment humidity：5%～...
- Page 10 4. Connecting PC via USB Cable or RJ45 Ethernet Cable 5. Remove ties on belts For transportation safety, ties were implemented to fixed machine laser head avoiding unexpected movement.
-
Page 11: Section Iv. Software
Section IV. Software 1. RDWorkV8 Installment... - Page 12 Choose "Laser work" Click “Install USB driver”...
- Page 13 After that, the USB driver have been installed Then install the software, click “Install”...
- Page 14 After Installment completed, click ”Exit” 2. RDWorks Interface Briefly...
- Page 15 Menu Bar：The main function of this software are available through the implementation of the Menu Bar. Execute the menu command is the most basic mode of operation. Menu Bar including: Document、Edit、Draw、Setting、Processing、View and Help. System Bar: On the System Bar, placed some most commonly command buttons which is chosen from the menu.
- Page 16 Section V. Operations 1. PC Connection Test Base on plug USB cable to machine. Please check whether there is good connection between RDC6442 and computer(see red rectangle frame) Click on setting first then use select USB:Auto connection and Exit.
- Page 17 2. Origin setting& Z height positioning That you would use focus gauge as below or auto-focus Focus Gauge and how to measure as below...
- Page 18 Auto-focus is a very useful function to align focal length automatically Press Focus on the RDC6442 Panel to allow machine find focus point automatically. Press Z/U and select Auto focus and Enter...
- Page 19 Once it’s done, move laser head to correct position and press “origin” to tell laser where to start with. 3. Pilot Run Test First, open file “hellokitty.plt” in RDWorksV8...
- Page 20 Then choose the parts you want to cutting or engraving marked by the Layer Bar. The color of object that is the color of the object contour. You can click the color button on the Layer Bar to change the color of the object has been selected. The color of the pressed button is the color of current layer.
- Page 21 Last, I will to cutting the frame of the picture. so i marked it as Red. setting cutting mode. speed 20mm/s, power 30%. Now the setting of the file is finised, Click "start", the machine will start working!
- Page 22 4. U Disk Operation UDisk function is very useful function when you start small production without a. Insert U disk as shown in blue arrow b. Click “SaveToUFile” to the U disk...
- Page 23 Press on the panel d. Move the cursor to Udisk+ by Arrow keys and Enter...
- Page 24 Then move the cursor to Copy to Mem and Enter f. Press St/Pau to start...
- Page 25 Laser machine should work as wanted! Section VI. FAQ 1. Why Machine does not move when power on? Answer: 1.Check the power cable good connection or not 2.Check the panel paraments if it is correct 2. Why No laser beam come out? Answer: Please check laser tube whether physical damage.
-
Page 26: Electrical Diagram
Electrical Diagram...
Need help?
Do you have a question about the HL-1060L and is the answer not in the manual?
Questions and answers