Summary of Contents for Santel Perfecta Micra
- Page 1 Wireless keypad PRF-LCD-WRL Firmware version 2.01 prf-lcd-wrl_en 01/23 SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND tel. + 48 58 320 94 00 www.satel.pl...
- Page 2 IMPORTANT The device should be installed by qualified personnel. Read carefully this manual before proceeding to installation. Changes, modifications or repairs not authorized by the manufacturer shall void your rights under the warranty. The name plate of the device is located on the enclosure base. The device meets the requirements of the applicable EU directives.
- Page 3 The PRF-LCD-WRL wireless keypad enables operation and programming of the PERFECTA control panels equipped with the WRL module. The PRF-LCD-WRL keypad with firmware version 2.01 is fully supported by PERFECTA control panels with firmware version 1.04 from 2022-05-17 (or newer) / 2.00 from 2022-05-17 (or newer).
-
Page 4: Installation
PRF-LCD-WRL SATEL 2. Description Operating modes When the keypad is powered by the APS-055 power supply, it operates similarly to a wired LCD keypad. When the keypad is powered by the batteries, it operates in one of the two modes: Wake-up –... - Page 5 SATEL PRF-LCD-WRL Be particularly careful during installation and replacement of the batteries. The manufacturer is not liable for the consequences of incorrect installation of the battery. The used batteries must not be discarded, but should be disposed of in accordance with the existing rules for environment protection. The keypad is designed for indoor installation.
- Page 6 PRF-LCD-WRL SATEL 9. If you want to connect the keypad to the APS-055 power supply, run the power wires through the opening in the enclosure base. Use flexible wires with a cross-section of 0.5-0.75 m 10. Using wall plugs (screw anchors) and screws, secure the enclosure base to the wall Select wall plugs specifically intended for the mounting surface (different for concrete or brick wall, different for plaster wall, etc.).
- Page 7 SATEL PRF-LCD-WRL 3.1 Adding the keypad to the system You can add the wireless keypad to the system by using either a computer with PERFECTA program installed, or an LCD keypad. The control panel allows for enrolling of up to 4 PRF-LCD-WRL keypads.
-
Page 8: Keypad Settings
PRF-LCD-WRL SATEL 2. Press successively to run the 1273.R function. EMOVE 3. Use the keys to select the keypad you want to remove. 4. Press 5. The type and serial number of the keypad to be removed will be displayed. 6. - Page 9 SATEL PRF-LCD-WRL Options To configure on the keypad the options described below, use the 212.O PTIONS and 211.A functions. LARMS Show partition 1 status [Show part.1] – if this option is enabled, the keypad LEDs and display indicate the status of partition 1. The keypad will indicate the status of partition 2 only after entering code by the user who has access to partition 2.
- Page 10 PRF-LCD-WRL SATEL auto 50%-100% – enabled: brightness 100%. Keypad backlight [27.KEYbacklight] – the way how the keys backlight will work. If the keypad is powered by the batteries, the backlight will work only when the keypad is woken up, and the available settings should be interpreted as follows: not present –...
-
Page 11: Operation
SATEL PRF-LCD-WRL The “Wake-up duration” is the maximum time, i.e. if the event signaling takes less time, the sleep mode will be resumed in the keypad earlier. It may take a few seconds for the keypad to wake up after the event occurred. Wireless keypad initial greeting [218.Connect msg] –...