Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for cytiva CU-950
- Page 1 CU-950 Installation guide Original instructions cytiva.com...
-
Page 2: In This Chapter
This instruction describes CU-950 and provides information on how to install it with ÄKTAexplorer, ÄKTAFPLC, ÄKTAmicro, ÄKTApilot™ and ÄKTApurifier. Prerequisites In order to operate CU-950 safely and according to the intended purpose the following prerequisites must be met: • You must read the Safety Instructions in this Installation guide. -
Page 3: Important User Information
Intended use CU-950 is intended for research use only, and shall not be used in any clinical or in vitro procedures for diagnostic purposes. Definitions This user documentation contains safety notices (WARNING, CAUTION, and NOTICE) concerning the safe use of the product. -
Page 4: Notes And Tips
A tip contains useful information that can improve or optimize your procedures. Typographical conventions Software items are identified in the text by bold italic text. Hardware items are identified in the text by bold text. In electronic format, references in italics are clickable hyperlinks. CU-950 Installation guide 11000325 AH... -
Page 5: Regulatory Information
1 Introduction 1.2 Regulatory information Regulatory information This section lists the directives and standards that are fulfilled by CU-950. Contact information for support To find local contact information for support and sending troubleshooting reports, visit cytiva.com/contact. Manufacturing information The table below summarizes the required manufacturing information. - Page 6 1 Introduction 1.3 Description Description CU-950 unit consists of a rear panel with connectors and three indicators (LEDs) on the front. The unit is supplied with a small power converter and EU and US mains cables. UniNet-1 Test Figure 1.1: CU-950 unit.
-
Page 7: Safety Instructions
2 Safety instructions Safety instructions This chapter describes the safety compliance, safety labels, general safety precautions, emergency procedures, power failure and recycling of CU-950. CU-950 Installation guide 11000325 AH... -
Page 8: Safety Precautions
2 Safety instructions 2.1 Safety precautions Safety precautions CU-950 is powered by mains voltage that may be hazardous. Before installing operating or maintaining the system, you must be aware of the hazards described in this manual. Follow the instructions provided to avoid personal injury or damage to the equipment. -
Page 9: System Operation
Do not operate CU-950 in any other way than described in the CU-950 and UNICORN manuals. WARNING Do not use CU-950 if it is not working properly, nor if it has suffered any damage, for example: • Damage to the power cord or its plug •... - Page 10 2 Safety instructions 2.1 Safety precautions WARNING Do not use any accessories or products not supplied or recommended by Cytiva. WARNING Do not remove any protection devices from the system. CU-950 Installation guide 11000325 AH...
- Page 11 2 Safety instructions 2.2 Safety and identification labels Safety and identification labels Figure 2.1: CU-950 rear panel with labels. Label Meaning This symbol indicates that the product contains hazardous materials in excess of the limits established by the Chinese standard SJ/ T11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronics.
- Page 12 2 Safety instructions 2.3 Recycling Recycling When a CU-950 unit is taken out of service, the different materials must be separated and recycled according to national and local environmental regulations. CU-950 Installation guide 11000325 AH...
-
Page 13: Cable Connections
Only use mains cables delivered and approved by Cytiva. Mounting CU-950 Hang the CU-950 on the left side of the system by inserting the hooks on the front of CU-950 into the rails on the side of the UV-900 or UPC-900 and rotating into position, as shown in Fig. - Page 14 3 Installation with ÄKTA lab systems Figure 3.2: Schematic UniNet-1 and mains cable connections for ÄKTAexplorer Figure 3.3: Schematic UniNet-1 and mains cable connections for ÄKTApurifier and ÄKTAmicro. CU-950 Installation guide 11000325 AH...
-
Page 15: Connecting The Cables
Mains supply socket UniNet-1-cable UniNet-1-cable Ethernet cable Mains cable Power converter Connecting the cables Step Action Connect the UniNet-1 data communication cable between the UniNet-1 port on CU-950 and Pump P-900 or Pump P-920 in the system. CU-950 Installation guide 11000325 AH... - Page 16 The CU-950 driver is available on the UNICORN installation CD and is normally installed together with UNICORN. Hang the CU-950 on the left side of the system by inserting the hooks on the front of CU-950 into the channel on the side of the UPC-900 and rotating into position, as shown in Fig.
- Page 17 This section describes the installation with ÄKTApilot. WARNING Only use mains cables delivered and approved by Cytiva. The CU-950 unit and the power converter is placed near or inside ÄKTApilot. Fig. 4.1, on page 17 shows the schematic CU-950 cable connections for ÄKTApilot.
- Page 18 Step Action Connect the UniNet-1 data communication cable between the UniNet-1 port on CU-950 and one of the UniNet-1 sockets on the controller rear panel inside ÄKTApilot. Note: If a fraction collector is used, connect the fraction collector UniNet-1 cable between the controller rear panel inside ÄKTApilot and the fraction collector,...
- Page 19 Page intentionally left blank...
- Page 20 Standard Software End-User License Agreement is available on request. All goods and services are sold subject to the terms and conditions of sale of the supplying company operating within the Cytiva business. A copy of those terms and conditions is available on request. Contact your local Cytiva representative for the most current information.
Need help?
Do you have a question about the CU-950 and is the answer not in the manual?
Questions and answers