ZooZ ZEN54 LR User Manual

www.getzooz.com
ask@getzooz.com
Z-Wave 0-10 V dimming control for LED fixtures
Ÿ
Great for 0-10 V LED drivers in LED panels
Ÿ
Smooth dimming with instant status updates
Ÿ
Installs behind your existing wall switch (on/off or momentary)
Ÿ
700 series Z-Wave chip for better range and faster control
Ÿ
Z-Wave Long Range for ultra reliable no-mesh communication
Ÿ
Advanced configuration including min and max brightness
Ÿ
Built-in Z-Wave signal repeater for boosted communication
Ÿ
SmartStart and S2 Security for a safer network
Ÿ
Model Number: ZEN54 LR
Ÿ
Power Input: 100-240 VAC, 50/60 Hz, max. 4.1 A, 984 W
Ÿ
Power Output: 100-240 VAC, 50/60 Hz, max. 4 A, 960 W
Ÿ
Maximum Load: 4 A (use with 0-10 V LED drivers only)
Ÿ
Range: Up to 300 feet line of sight (or up to a mile with LR)
Ÿ
Operating Temperature: 32-104° F (0-40° C)
Ÿ
Installation and Use: Indoor only
Ÿ
CAUTION
This is an electrical device - please use caution when installing and
operating the 0-10 V Dimmer. Remote control of appliances may result
in unintentional or automated activation of power.
Do not use this Z-Wave device to control electric heaters or other
appliances which produce the risk of fire, burns, or electrical shock
when unattended.
To reduce risk of overheating and possible damage to other equipment,
do not install this unit to control a receptacle; a motor-operated
appliance; a fluorescent lighting fixture; any device over 32 V DC power;
or a transformer-supplied fixture. Use with 0-10 V LED drivers only.
BEFORE YOU INSTALL
This device is intended for installation in accordance with the
National Electric Code and local regulations. It is recommen-
ded that a licensed electrician perform this installation.
1. CHECK THE LOAD: don't exceed 4 A for your 0-10 V
Dimmer, USE ONLY WITH 0-10 V LED DRIVERS
2. POWER OFF: turn the circuit power off in the breaker panel
before you start. If installing in a multi-switch box with
multiple circuits, turn power off at all of the circuits.
3. CHECK THE WIRES: mark 0-10 V driver connections (GND-
and 0-10 V+), power (L and N), load to LED driver (LOAD) and
switch connections (SW and GND). Don't rely exclusively on
your multimeter to identify the wires!
µ
NOT SURE WHAT YOU'RE SEEING? WE'LL HELP! SUPPORT.GETZOOZ.COM
SEND US PICTURES OF YOUR SET-UP, BEFORE YOU DISCONNECT WIRES.
4. DISCONNECT THE SWITCH: remove the wires between the
switch and the LED driver and label them accordingly.
5. CONNECT THE 0-10 V DIMMER: follow all installation steps
carefully. Wire the device EXACTLY like in the diagram.
Depending on your set-up, you may need to install the device
at the LED fxture rather than in the switch box.
ON/OFF OR MOMENTARY SWITCHES ONLY
Do not connect the ZEN54 to a wall dimmer,
illuminated switch, or electronic add-on switch. The ZEN54
device can only be wired with on/off or momentary wall
switches. Physical dimming available from momentary
switches only. With on/off switches, dim via Z-Wave only.
USER MANUAL
0-10 V DIMMER
ZEN54 LR
FEATURES
SPECIFICATIONS
WIRING: READ IT!
PAGE 1
ZEN54 WIRING DIAGRAM FOR 0-10 V LED DRIVERS
1 Connect the driver wires to GND - and 0-10V+ on ZEN54.
2 Connect the wall switch to the GND- bundle and the
SW pigtail on the ZEN54.
3 Connect the LOAD on the ZEN54 to the line input on
the LED driver.
4 Connect neutral from the 120 V power source to N on
ZEN54 and the neutral input on the LED driver.
5 Connect line from the 120 V power source to the L
pigtail on the ZEN54.
GND 0-10V
QUESTIONS?
ask@getzooz.com
COMPLETE INSTALLATION
Secure your Z-Wave 0-10 V Dimmer and the wall switch in the
box with mounting screws, handling the wires with care.
Install the wall plate and restore power to the circuit.
Z-WAVE CONTROL
1. ADD DEVICE to your hub
Initiate inclusion (pairing) in the app (or web
interface). Check Long Range if using.
Not sure how? Scan one of the QR codes
below for step-by-step instructions or get in
touch: www.support.getzooz.com
2. Finalize inclusion at the dimmer.
TAP THE Z-WAVE BUTTON 3 TIMES QUICKLY
if using traditional Z-Wave inclusion.
SCAN THE QR CODE / ENTER THE 5-DIGIT PIN
if using the new SmartStart method.
The SmartStart security PIN is located on the back
of the relay, next to the Z-Wave Plus logo.
The LED indicator will blink green to signal communication
and turn green for 2 seconds if inclusion is successful or turn
red for 2 seconds if the pairing attempt fails.
NEED SOME HELP? ask@getzooz.com
Choose your hub and scan the QR code with your phone's
camera. Then click on the link to access the step-by-step
pairing instructions.
Z-Box Hub Hubitat
Get more tutorials and helpful tips at ww.support.getzooz.com
Register your product for extended warranty and
direct access to firmware files: getzooz.com/register
0-10 LED DRIVER
L N
GND-
0-10V+
SW
LOAD
L
ZEN54
N
120 V POWER
SmartThings
Home Assistant
PAGE 2
L N
0-10 V Dimmer ZEN54 LR
FCC ID: 2AZ2V-081822ZEN54
Power: 100-240V~, 50/60Hz
Max Load: A 4
Freq: 908.42MHz
SmartStart
Firmware: 1. 0 1
PIN: XXXXX
5021636