Advertisement
4.2.
OPERATING
WARNING! Ensure you have read, understood and apply safety instructions.
4.2.1.
Connect the die grinder to the air supply.
4.2.2.
To start, hold firmly and push the trigger locking lever forward whilst depressing trigger.
4.2.3.
The bit must be running at its maximum speed before attempting to grind the workpiece.
4.2.4. Slowly and smoothly bring the grinding bit toward the workpiece (avoid jerky movements).
Exert adequate pressure on the die grinder to grind according to the type and size of the
material you are working with. Avoid subjecting bit to excessive strain or harsh impacts.
Always hold die grinder firmly and ease grinding bit against workpiece. Maintain a
controlled progression.
DO NOT allow die grinder to free run for an extended period of time as this will shorten its
life.
5.
MAINTENANCE
WARNING! Disconnect die grinder from air supply before changing accessories, servicing or
performing maintenance. Replace or repair damaged parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
5.1.
If air supply does not have an oiler, lubricate the air die grinder daily with a few drops of
Sealey air tool oil dripped into the air inlet to prolong its life.
5.2.
Clean the die grinder after use.
5.3.
Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or
type of hose connectors. To remedy check the air supply and follow instructions in
chapter 3.
b) Grit or gum deposits in the die grinder may also reduce performance. If your model has
an air strainer (located in the area of the air inlet), remove the strainer and clean it. Flush
the die grinder out with gum solvent oil or an equal mixture of SAE No 10 oil and
paraffin. Allow to dry before use.
5.4.
For a full service contact your local Sealey service agent.
5.5.
When not in use, disconnect from air supply, clean die grinder and store in a safe, dry,
childproof location.
5.6.
Periodically lubricate crown and pinion gear with general purpose grease through the grease
nipple on head.
The SA653.V2 Air Die Grinder Midi size 90°Super Duty when operated in accordance with these instructions and tested in
accordance with EN 28662-2: 1994 results in the following vibration emission declared in accordance with BS EN12096: 1996.
Measured vibration emission value: ...................... 2.5m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome: This item represents a low Hand Arm Vibration risk
to users. The calculated maximum usage period exceeds 8 hours. We recommend appropriate safety equipment is utilised and
regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive strain injury.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Risk of Hand Arm Vibration Injury.
Uncertainty: ............................................. 1.0m/s²
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
SA653.V3 Issue: 3 - 11/11/09
Advertisement
