Related Manuals for Cielsa Dawn E021
Summary of Contents for Cielsa Dawn E021
- Page 1 INSTALLATION AND USER GUIDE APPLICABLE MODEL:E021 Installtion for electronic door lock Please read this manual before installing. cielsadawn@hotmail.com | www.cielsadawn.live...
- Page 2 TABLE OF CONTENT CHECK AND PREPARATION INSTALLTION STEPS INSTRUCTION OPERATION SAFETY PRECAUTIONS...
- Page 3 Required tools WELCOME This guide will walk you through step-by-step how to install and get your product up and running. Installation generally takes less than 30 minutes. If you have any questions, please feel free to contact...
- Page 4 Check and preparation ge contains the following components Before getting started, ensure the packa remove existing deadbolt or use provided template to bore new holes Check dimensions...
- Page 5 How to bore new holes? Put the template on the door panel as shown in the drawing. use the Template as an indication to mark the centre of the circle on the door face and the centre of the door edge.
- Page 6 Installation Steps ADJUST DEADBOLT AND INSTALL Insert the deadbolt into mortise.Secure with 2 screws.
- Page 7 INSTALL THE KEYPAD Possi doluptam et parchitatur rempore, volum versper eprovitatiae exerchi llander- it vid quis cus eostin pra vel essitibusdam qui vellupturi omniae venihit lab. Install front panel and front panel silicon pad, make sure the latch bolt be contracte. FIXING OF REAR PANEL Pass the IC wire and the latch link bar to mounting plate.
- Page 8 INDENTIFY DOOR HANDING The door is “Left-handle” if the hinges are on the The door is “Right-handle” if the hinges are on left side of the door. the right side of the door. Turn the piece as shown Rotate the thumb turn piece as shown...
- Page 9 INSTALL REAR PANEL: Rotate the thumb turn piece as shown Docking of the connector. Pay attention to the direction of the inserted connector. Install the rear panel. Use the screws as shown connect rear panel with latch and rear panel fixing plate. •...
- Page 10 Instruction operation SYSTEM SIGNALS Ⅰ use cases Sound Light Correct user code entered to unlock 3 short beeps Blue flashes Successfully locked 3 short beeps Blue flashes Incorrect user code entered 4 short beeps white flashing Successful programming 2 short beeps None Unsuccessful programming 4 short beeps...
- Page 11 TEST Ⅱ You have complet ed the installation.Before setting up, you can use the follow methods to test whether the installation successfully or not. 1. The key function: Insert the key into the key hole directly to test. 2. The keypad function: Press the lock key for a long time to lock;The factory status code is “123456 “, press “123456”...
- Page 12 SYSTEM RESETTING Ⅲ a.Removing one of the b.Touch anywhere on C. Install the battery back. Battery When the “1” of the key- the keyboard board flashes,long press the Anti-Lock Switch for 10 seconds. You will hear two beeps and a fast flashing blue light, and then a long beep means that the lock is restored to the factory settings.
- Page 13 USER SETTING Ⅳ Move swiftly during programming. If no digit is pressed for 10 seconds, the system will time out and you will need to restart the procedure. Enter new Press Press Enter new admin admin code “ ” code again “...
- Page 14 ADD GENERAL USER’S CODES (CAN BE ADDED CONTINUOUSLY) Press Enter new user Press Enter new Press Enter admin code “ ” password again “ ” user passwprd “ ” (6-12bit) Press ” 1 “ Enter admin fingerprint Press user finger four times •...
- Page 15 CHANGE ADMIN CODE Enter new Press Enter new Press Press Enter Press Enter old admin code “ ” “ ” admin code “ ” admin code “ ” admin code again Press (6-12bit) ” 2 “ press finger four times Enter old admin fingerprint •...
- Page 16 CHANGE GENERAL USER’S CODE Enter new Press Enter new Press Enter Press Enter old Press user code “ ” user code “ ” admin code user code “ ” “ ” aga in Press (6-12bit) ” 2 “ Enter admin fingerprint press user finger four times Enter old user fingerprint eg, if your admin code is “555555”...
- Page 17 eg, if your admin code is “555555“ or fingerprint and you want to change the old user fin- gerprint which ID is 002 into a new password”111111”.After the change,the ID of the new password still is 002 ,the enter steps are as follows: press old user fingerprint 111111 111111...
- Page 18 DELETION OF ALL USERS NORMALLY OPEN MODE (EXCEPT ADMINISTRATOR) (THERE WILL BE POTENTIAL SAFETY HAZARD AFTER USING THIS FUNCTION ,IT IS NECESSARY TO FULLY UNDERSTAND BEFORE USING IT.) Enter Press admin code “ ” Press Press Press Enter 00000 Enter admin password “...
- Page 19 SPECIFICATION PARAMETER NOTE: 1. The lock is only subjected to simple waterproofing, and must not be exposed to rain, in order to avoid damage caused by water intrusion into lines. 2. The lock is not fireproof, so it is not suitable for installation on the fire doors with waterproof requirements.
- Page 20 Cielsa Dawn® www.cielsadawn.live cielsadawn@hotmail.com...
Need help?
Do you have a question about the E021 and is the answer not in the manual?
Questions and answers