Related Manuals for Mist MRO002
Summary of Contents for Mist MRO002
- Page 1 Instruction Manual Please read and save these instructions. MRO002 Reverse Osmosis System...
- Page 2 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modi cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
-
Page 3: Table Of Contents
Contents Installation Instructions Before Installation............................................1 Parts List ................................................1 Product Introduction ............................................2 Installation Sample............................................3 Installation Tips ..............................................3 Installation Steps..............................................4 Step 1: Connect to the Cold Water Supply..................................4 Step 2: Install the Drain Saddle .......................................4 Step 3: Install the RO Faucet........................................5 Step 4: Connect Tubing ..........................................5 Step 5: Start up the System ........................................6 Filter Replacement Schedule........................................6 Filter Life Reminder............................................6... -
Page 4: Installation Instructions
• Drill bit: 1/4" (for drainpipe), 1" (for faucet hole) Specifications To achieve optimal performance, it is highly recommended that the system be used only within these operational parameters. Model MRO002 Size(L*W*H) 17.1"*5.5"*14.8" Feed Water Pressure 14.5-87 psi/0.1-0.6 MPa Feed Water Temperature 41-100 °F / 5-38 °C... -
Page 5: Product Introduction
Product Introduction Filter life indicator PURE DRAIN INLET Filtering Power indicator indicator TDS indicator Filter service life indicator Filtering indicator • When the system is ushing, the ltering indicator light ashes. • When the system is making water, the ltering indicator turns steady blue. Filter life indicator •... -
Page 6: Installation Sample
Installation Sample Kitchen Faucet RO Faucet Feed Water Adapter Inlet Water Tubing Pure Water Tubing Cold Drain Water Power Tubing Installation Tips How to Drill a Hole in Your Sink or Countertop (Optional) NOTE: Con rm if there is an existing hole available to install the RO faucet. If not, drill a hole according to the following steps. -
Page 7: Installation Steps
Installation Steps Step 1: Connect to the Cold Water Supply CAUTION: DO NOT CONNECT THIS WATER LINE TO A HOT WATER SUPPLY LINE. The water supply to the unit MUST be from the COLD WATER LINE. Using HOT WATER will severely damage your lters. a. -
Page 8: Step 3: Install The Ro Faucet
Step 3: Install the RO Faucet Faucet Spout a. Insert the faucet spout into the faucet body. b. Insert the faucet stem into the faucet base, then insert the faucet stem through the hole in the countertop. Faucet Body c. Under the sink, slip on the other parts in the order shown in the Faucet Base diagram. -
Page 9: Step 5: Start Up The System
Step 5. Start up the system a. Turn on the cold water supply. Check for any leaks in the system. b. Insert the faucet power cord which is connected to the faucet into the “FAUCET” connector at the back of the the RO ltration unit housing and tighten the nut. -
Page 10: Filter Replacement Guide
Filter Replacement Guide Turn o faucet and wait for 30 seconds to fully release the pressure on the system. The lter can be replaced without turning o the water source or power supply. a. Twist the lter that needs to be replaced counterclockwise; b. -
Page 11: System Maintenance
System Maintenance If you do not use the machine for a long time (more than 1 week), it is recommended that the faucet be opened to ush for a while before the water is used again. Please replace the lter regularly according to the lter life indicator. NOTE: While testing was performed under standard laboratory conditions, actual performance may vary depend- ing on the source water quality and water usage. -
Page 12: Troubleshooting
Troubleshooting If the System Cannot Be Powered on After You Insert the Power Plug a. Check the ow of electricity to the power outlet under the sink as this problem most often occurs when there is no ow of electricity to the outlet. Also, check to ensure that the system has been plugged correctly into the outlet. To test if there is a problem with the system itself, just pick up the system and try another power outlet. -
Page 13: Limited Product Warranty
Booster Pump Starting and Stopping Frequently a. Reminder Buzzer beeps 5 times, and then the lter life indicators on the front panel ash purple. b. There is an internal pressure imbalance: Disconnect the power. Turn o the RO faucet completely, removing any tubing crimps. - Page 14 REVERSE OSMOSIS SYSTEM FOR EASY REORDER FOR EASY REORDER Use the camera app Use the camera app on your smartphone to on your smartphone to scan this QR code. scan this QR code. Use code REORDER for Use code REORDER for 10% off...
- Page 15 主机 说明书 此页不印刷 印刷品技 术 要求 IMPORTANT PRINTING CAUTION 1 . 印刷 要求 覆 光 膜 覆 亚 膜 U V 油 吸 塑油 过 油 丝印 2 . 材质 要求 封面封底200g铜版纸覆亚膜，内页105g铜版纸 3 . 颜色 要求 四色印刷 图 像 颜 色请 依 据 数码 稿 印 刷 请...
Need help?
Do you have a question about the MRO002 and is the answer not in the manual?
Questions and answers