Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Swisson XRC-CT15
- Page 1 XRC-CT15 External Trigger Contacts for XRC-150 User Manual...
- Page 2 XRC-CT15 External Contacts Trigger for XRC-150 User Manual Issue 1 (2007-26-02) Copyright © 2007 SWISSON AG No part of this documentation may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, without the prior written permission of SWISSON AG.
-
Page 3: Table Of Contents
Table of contents Table of contents ........... 3 Overview............4 General Description ........5 Connecting the XRC-CT15 to the XRC-150 .. 6 Connection ..........6 Connecting Cable ........7 Opening the XRC-CT15......... 8 Connecting contacts to the XRC-CT15..9 Using internal Power ........9 Using external Power ......... -
Page 4: Overview
The XRC-CT15 is connected with the XRC-150 through this port. Cable Glands Glands for cables connected in the XRC-CT15 The lid of the XRC-CT15 can be removed for connection of the contacts Lid Screw This screw holds the lid on the XRC-... -
Page 5: General Description
General Description The XRC-CT15 is an accessory for use with the XRC-150. On this device up to 15 external trigger contacts can be connected. With these contacts the XRC-150 can be controlled remotely: Contacts 1 .. 15 XRC-CT15 XRC-150 Each button can be configured to start, stop or... -
Page 6: Connecting The Xrc-Ct15 To The Xrc-150
Connecting the XRC-CT15 to the XRC-150 Connection The XRC-CT15 can be easily connected to the XRC-150 through running a cable from an external port of the XRC-150 to the XRC-CT15: It doesn’t matter on which port (port #1 or #2) the... -
Page 7: Connecting Cable
Connecting Cable The connection of the XRC-CT15 to the XRC-150 is done with a standard RJ45 8 pole STRAIGHT network cable: The speed of the data transmission between the XRC-CT15 and the XRC-150 is 250 kBaud. Therefore, the cable mustn’t be very high quality. -
Page 8: Opening The Xrc-Ct15
Opening the XRC-CT15 To connect the XRC-CT15 with external trigger contacts, the lid must first be removed. Simply remove the lid screw: Lid Screw Slide out the lid of the XRC-CT15: Now you can see the connecting ports (1 – 15) for... -
Page 9: Connecting Contacts To The Xrc-Ct15
(VCC) of the XRC-CT-15, and the other connection to a dedicated input of the device: XRC-CT15 Using external Power When using external power, it’s necessary to connect GND of the XRC-CT15 to the voltage reference (ground) on the external device: XRC-CT15 External Device Voltage of... -
Page 10: Configuration
Configuration Every time a contact is activated, the XRC-CT15 sends this information to the XRC-150. Therefore it’s possible to configure each contact activity on the XRC-150 to either start, stop or pause, a sequence. To configure the contacts, go to the menu point “External Devices”... -
Page 11: Technical Data
Technical Data Absolute Maximum ratings The maximum ratings of the XRC-CT15 mustn’t be exceeded; otherwise the device will be damaged. Input voltage of contacts (1 – 15) when using external power VCC current (if you 250mA want to power another device) Operating Conditions 7V –... -
Page 12: Safety Notes
This device is developed for only use together with the XRC-150 Dynamic DMX Recorder of SWISSON AG and no other devices. • Clean the XRC-CT15 only with a soft, damp cloth. Don’t use chemicals or other harsh scrubbing agents. •...
Need help?
Do you have a question about the XRC-CT15 and is the answer not in the manual?
Questions and answers