Advertisement
Quick Links
Advertisement
Summary of Contents for Prime Tech WF08
- Page 1 ELECTRIC WINCH WF08 WITH A CAPACITY OF 12000lb...
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS Warning! Observe safety precautions for personal safety and the safety of others. Improper equipment operation may cause personal injury and equipment damage. Read the following carefully before attempting to operate your winch and keep the instructions for future reference. 1. - Page 3 WINCH OPERATION WARNINGS Read the following carefully before attempting to operate your winch and keep the instructions for future reference. 1． The uneven spooling of cable, while pulling a load, is not a problem, unless there is a cable pile up on one end of the drum. If this happens reverse the winch to relieve the load and move your anchor point further to the centre of the vehicle.
- Page 4 16.Winch Cable: -Be sure that the cable is in good condition and is attached properly. -Do not use the winch if cable is frayed. -Do not move the vehicle to pull a load. -Do not replace the cable with a cable of lesser strength. -The life of the cable is directly related to the use and care it receives.
- Page 5 INSTALLATION MOUNTING YOUR WINCH 1a)The winch is to be mounted into a suitable steel mounting frame using the 4 point foot mounting system in either a horizontal or vertical plane. b) It’s very important that the winch be mounted on a flat surface so that three sections (motor, cable drum and gear housing) are properly aligned.
- Page 6 LECTRICAL CONNECTION For normal self-recovery work, your existing electrical system is adequate. A fully charged battery and proper connections are essential. Run the vehicle engine during winching operations to keep battery charged. Pay chose attention to proper electrical cable connection as follows (refer to Diagram 1) 1.
-
Page 8: Operation
WINCH OPERATION SUGGESTION: The best way to get acquainted with how your winch operates is to make a few test runs before you actually need to use it. Plan your test in advance. Remember you can hear your winch as well as you can see it operate. - Page 9 Winching capacity 1. This winch has a capacity of 12000lbs 2. Pulling capacity is reduced as the incline increases. Recommended safe loads for various inclines are listed in table below: Rated Line Pull 100% 1500lb 7538 5102 3233 2496 2134 1928 2000lb 10050...
- Page 10 Press “►” on control box, use hand remote control. Level the Shift switch when winch is not in use Press “◄”on control box, use wireless remote control level the Shift switch when winch is not in use...
- Page 11 12000LBS FEATURES AND SPECIFICATIONS Single Line Rated Pull 12000lb (5440kg) Motor 12V 6.6hp/ 4.8kw, 24V 4.0hp/3.0kw,series wound control Remote Switch, 12ft (3.7m) lead Gear train 3 Stage Planetary Gear reduction ration 187.2:1 Braking Action Automatic In-The-Drum Cable 94ft of 3/8〞diameter (28m of 9.1mm diameter) Main body Sealed Effected protection...
- Page 12 12000LBS LINE PULL AND CABLE CAPACITY Layer of cable Rated line 12000 9210 8030 6894 pull per layer 5440 4170 3640 3125 Cumulative cable capacity 12000LBS WINCH PARTS LIST Item Part No.- Description Item Part No. Description 12000Ibs 12000Ibs 0107/08-01 Transmission Shaft 0107/08-15 Nylon Bearing...
- Page 13 OLENOID BOX ASSEMBLY (12V/24V) PARTS LIST Item No. Part No. Description So107/08-30 Cover-solenoid Ass’y So107/08-31 Cable(Brown 0.75mm X25cm; to the battery”+”) So107/08-32 Cable(Brown 0.75mm X25cm; Power in) So107/08-33 0.425m Short Black Cable with Yellow Terminal Sleeve So107/08-34 Bracket So107/08-35 ScrewM5X12 So107/08-36 Solenoid-Power in 12V So107/08-36A...