Table of Contents
Advertisement
Quick Links
1938
Drum Sander
Operating Instructions
Producer:
Laguna Tools Inc
744 Refuge Way, Suite 200
Grand Prairie, Texas 75050
USA
Phone: +1 800-234-1976
Website: www.lagunatools.com
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: +420 220 950 910
PDF ONLINE
E-mail: sales@igmtools.com
www.igmtools.info
Website: www.igmtools.com
2023-02-23
151-1938 LAGUNA Drum Sander Manual EN v1.0.1 A4ob
Advertisement
Table of Contents
Related Manuals for IGM LAGUNA 1938
Summary of Contents for IGM LAGUNA 1938
- Page 1 Laguna Tools Inc 744 Refuge Way, Suite 200 Grand Prairie, Texas 75050 Phone: +1 800-234-1976 Website: www.lagunatools.com Distributor: IGM nástroje a stroje s.r.o. Ke Kopanině 560, 252 67, Tuchoměřice Czech Republic, EU Phone: +420 220 950 910 PDF ONLINE E-mail: sales@igmtools.com www.igmtools.info...
-
Page 2: Ec Declaration Of Conformity
Conform with the essential safety requirements of the relevant European Directive: - Machinery Directive 2006/42/EC - Electromagnetic Compatibility Directive 2014/30/EU The person who compile technical file established within the EU: Name: IGM nastroje a stroje s.r.o. Address: Ke Kopanine 560, Tuchomerice , CZ-252 67 Tel.: +420 220 950 910 Email: sales@igmtools.com... - Page 3 Laguna Tools machine. This manual has been prepared for the owner and operators of an IGM LAGUNA 1938 SuperMax Drum Sander to promote safety during installation, operation and maintenance procedures.
-
Page 4: Machine Specification
Loose sanding belt can cause injury. The workpiece may bounce off the designed to operate in closed rooms and must be placed stable on a sanding belt and turn against the machine operator. firm and levelled ground. The machine requires assembling. Danger of thrown workpiece. - Page 5 3. Cut each corner of BOX 1 to fold sides flat, providing access to sanding unit. 4. Connect the second leg sub-assembly to the top long rails. 4. With one or two helpers, place the sanding unit on stand or bench (lift points marked).
- Page 6 NOTE: Leave the silver plate, which is near the fast lever and 6. Install knob to height adjustment handle. First, finger tighten nut to under the motor, in place when removing bolts. knob. Thread stud from knob into hand wheel and tighten nut against hand wheel.
-
Page 7: Setting And Adjustment
2. Locate the height adjustment handle for raising and lowering the 13. Plug the short power cord that is attached to the motor into the outlet sanding head. on the control box. This cord will provide switched power for the motor when the machine is plugged into the power source. - Page 8 If the drum is not parallel, loosen the 4 socket head screws A (these screws Installing and Wrapping Abrasives (continued) are along the outboard (left) side of the conveyor belt) and raise or lower the UNPLUG THE MACHINE FROM THE POWER SOURCE! conveyor with the adjustment nut B to achieve parallel alignment.
-
Page 9: Machine Operation
NOTE: Take notice that for detail only the drum was removed to show the inboard (right) take-up fastener. 7. Machine Operation Proper Abrasive Position Position the abrasive in the slot with sufficient room between the inside of the slot and the tapered end of the wrap to allow it to be pulled into the drum as needed. - Page 10 Button Reference and Use Calibration It is helpful to familiarize these buttons and their purpose with the Wixey There are three typical variations of calibration. The first variation (Type 1) is for the DRO to show the sanded thickness of the material.
-
Page 11: Conveyor And Speed Rate
changes the readout from “ABS” to “INC” and zero’s the readout on top of bowed or otherwise varied in thickness from end to end. If possible, the just sanded piece. Now the readout will show support such stock as it is being sanded to keep it from slipping or tipping. the amount of stock removed per sanded pass in “INC”... -
Page 12: Conveyor Belt Tracking
Unplug the machine from the power source! 1. Raise the drum carriage to its highest position. Unplug main drive Optional Accessories: motor from receptacle on the machine. IGM Stick Abrasive Cleaner Order code: MCBP Abrasives Up to date offer at www.igmtools.com 2. -
Page 13: Troubleshooting
9. Troubleshooting Any operating problems will likely occur during the period of becoming familiar with the sander. If you are experiencing a problem affecting the machine’s performance, check the following listings for potential causes and solutions. Also review the previous sections in this manual on setting up and operating your machine. -
Page 14: Wiring Diagram
19-38 - WIRING DIAGRAM www.igmtools.com -14-... -
Page 15: Head Assembly
19-38 - HEAD ASSEMBLY www.igmtools.com -15-... -
Page 16: Parts List - Head Assembly
19-38 - PARTS LIST - HEAD ASSEMBLY # PART NO DESCRIPTION SIZE # PART NO DESCRIPTION SIZE 480DS- 85 480BS-196 HEIGHT DIRECTION LABEL MOTOR -101E 86 480BS-186 MAINTENANCE LABEL 480BS-194- 87 480BS-187 WARNING LABEL STRAIN RELIEF, MOTOR PG-11 88 480BS-1105 LOCK WASHER 3 480DS- MAIN CORD, MOTOR TO CONTROL 89 480BS-1104 HEX NUT... - Page 17 19-38 - CONVEYOR AND MOTOR www.igmtools.com -17-...
-
Page 18: Parts List - Conveyor And Motor
STRAIN RELIEF, GEAR MOTOR PG-9 45 480BS-245 HEX NUT 5/16”-18 47 480BS-247 HEX CAP SCREW 1/4”-X1/2” IGM nástroje a stroje s.r.o., Ke Kopanině 560, Tuchoměřice, 252 67, Czech Republic, EU +420 220 950 910, www.igmtools.com © 2023 IGM nástroje a stroje s.r.o.