Advertisement
Quick Links
Jet-ski with motor boat engine
Please Note
The OPITEC range of projects is not intended as play toys for
young children. They are teaching aids for young people lear-
ning the skills of Craft, Design and Technology. These projects
should only be undertaken and operated with the guidance of a
fully qualified adult. The finished projects are not suitable to
give to children under 3 years old. Some parts can be swallowed.
Danger of suffocation!
Content
Hull
Plywood
Wooden bar
Wooden bar
Aluminium sheet
Brass pipe
Round brass bar
Propellor (clockwise-turning)
Wire connectors
Washers
Silicon tube
Mounting bracket
Motor
1
117.178
Tools required:
Wood glue
Vice with ben-
(water resis-
ding support
tant)
Round file
Drills
Engineer's file
Soldering iron
Quantity
Dimensions( mm)
1
280x100
2
300x210x3
2
250x5x5
1
50x10x5
1
200x200x0,3
1
ø3x100
1
ø2x245
1
1
12
7/3,2
1
1/3
1
ø21
1
Ruler
Scissors
ø2
ø3
ø4
Sandpaper
Jigsaw
Phillips
Metal cutters
screwdriver
Designation
Hull
Base & individual parts
Frame
Engine bracket
Aluminium parts
Brass pipe
Round brass bar
Propellor
Fastening rudder
Fastening rudder
Connection motor & shaft
Engine fastening
Motor
Pencil
Super glue
Adhesive tape
Part no.
1
2
3
4
5
6
7
8
9
10
11
12
13
Advertisement
Summary of Contents for Opitec 117.178
- Page 1 Drills Jigsaw Please Note The OPITEC range of projects is not intended as play toys for young children. They are teaching aids for young people lear- ning the skills of Craft, Design and Technology. These projects should only be undertaken and operated with the guidance of a fully qualified adult.
- Page 2 Instructions 117.178 Jet-ski with motor boat engine Content Quantity Dimensions( mm) Designation Part no. Wire, red Cabling Metal axle ø3x70 Fastening rudder Phillips metal screw 2,9x13 Fastening Cylinder head bolt 25xM3 Fastening Cap nut M3 Fastening person Cylinder head bolt...
- Page 3 Instructions 117.178 Jet-ski with motor boat engine Glue the individual pieces A, B,C,E, H + I together as shown. Let the Glue the template (page13+15) together, copy on to the aluminium glue dry properly. sheet and cut out the individual parts with metal cutters. Clean up the edges with an engineer‘s file.
- Page 4 Instructions 117.178 Jet-ski with motor boat engine ø3 Drill a hole (ø3 mm) in the bottom of the hull, 75mm away from the Shorten the metal axle (15) to approx. 40mm. Wrap the rudder (5c) around the axle as shown above and glue it on. Then insert into the edge of the stern.
- Page 5 Instructions 117.178 Jet-ski with motor boat engine Fit the switch (22) into the designated opening in the construction as Then insert the batteries and place the top of the jet-ski on to the shown. Connect the red cable from the battery holder to the central frame in the deck.
- Page 7 Instructions 117.178 Jet-ski with motor boat engine Template Scale 1:1...
- Page 9 Instructions 117.178 Jet-ski with motor boat engine Template individual pieces Scale 1:1...
- Page 11 Instructions 117.178 Jet-ski with motor boat engine Template individual pieces Scale 1:1...
- Page 13 Instructions 117.178 Jet-ski with motor boat engine Template aluminium sheet Scale 1:1...
- Page 15 Instructions 117.178 Jet-ski with motor boat engine Template aluminium sheet Scale 1:1...