Related Manuals for Geovent GEOFILTER GFB2 W3
Summary of Contents for Geovent GEOFILTER GFB2 W3
- Page 1 I N S T R U C T I O N M A N U A L G E O F I L T E R G F B 2 W 3 GFB2 W3 3-1, GFB2 W3 6-2, GFB2 W3 9-3, GFB2 W3 12-4 www.geovent.com Version 1.0 02.01.2023...
-
Page 3: Table Of Contents
The manual must be read in full and understood before Do not modify the product or use spare parts from other interacting with the product. suppliers than Geovent, as this may hamper the product and the function. When the manual has been read and understood in full,... -
Page 4: Machine Oveview
Place the product on a solid, flat foundation (e.g. a con- Air pressure tank: Powder coated crete floor) and anchor it. Allow space to perform filter changes. Automatic control: Cleaning control with digital display for adjusting cleaning time, cleaning interval, and shut When you change the filter cartridges, follow the instruc- down cleaning. -
Page 5: Transport, Handling And Storage
4.0 Transport, handling and storage 2. Attach the product to a circular duct on both the clean side and the dirty side (the bottom tube connection is always the dirty side). Remember to seal the connec- During transport in a truck or in another means of trans- tion with joint fi ller and/or tape! portation the product must be securely packed in a box or a pallet and covered with a water proff material. -
Page 6: Timer Control Panel
6.0 Timer control panel List of Functions F02: Pulse time. 6.1 Operating the filter Possible values: 0.5 - 5.00. Step 0.01 Default = 0.20 The filter is delivered as standard with timer control. F03: Pause time, cetween shots: Possible values: 001 - 999. Step 1 Default = 175 F04: Number of valves. - Page 7 Alarms: The unit runs a number af checks during the start-up cycle and during normal operation. The possible alarms and respective solutions are shown in the following table. Alarm Description Action 24Vdc, switch the device off and move the ac/dc jumpers to dc. F05 set to 24Vdc - ac jumper detected.
- Page 8 Connection diagram Connections diagram 9 ...
-
Page 9: When The Product Has Been Installed
6.2 When the product has been installed • Regularly check the filter’s clean side for dust particles and change filter cartridges in the event of leakage. When assembly of the filter is complete, installed corre- ctly and ready for use, there will not be any interaction Alarm between the user and the filter besides emptying the bucket. - Page 10 6. Empty the bag for air. 1. Disconnect valve. 7. Use a strip to close the bag. 2. Pull the handle up. 8. Put a new bag in the bucket. Make sure the bag is placed correctly. Avoid breaking the bag when the bucket is placed back in position.
-
Page 11: Replacing The Filter Cartridges
Opening and closing the door to take the necessary personal safety precautions such as wearing a respirator and gloves that meet the Working Environment Authority’s rules for working with contaminated dust. 3. Loosen all screws on the top door of the filter unit. 4. -
Page 12: Cleaning
the particles on the textile of the filter to be blown off and collected in the bucket below. Do not open the doors during operation to avoid injury. Cleaning of the inside of the product is not recommended. When the doors of the product are opened, you must wear protection gloves, eye protection and a suit cove- ring your body. -
Page 13: Dismantling, Disabling And Scrapping
10.0 Dismantling, disabling and scrapping Deactive the product by disconnection the electrical mains. Dismantle the compressed air pipes and other tubes etc. When you dispose of the product you should dismantle the filter elements as described in chapter 7.3. It is very important that the instructions of this ma- nual is followed in order to avoid contamination of people and the environment! The inside of the product must be cleaned by means of... -
Page 14: Documents And Drawings
11.0 Multi coupling diagram... - Page 15 Dimensions Dimensions GFB2 W3-3-1 GFB2 W3-6-2 Inlet mm: ø315np Inlet mm: ø315np Outlet mm: ø315np Outlet mm: ø315np...
- Page 16 Dimensions Dimensions GFB2 W3-9-3 GFB2 W3-12-4 Inlet mm: ø400np Inlet mm: ø500np Outlet mm: 2xø315np Outlet mm: 3xø315np...
-
Page 17: Liability
The product: GFB2 filter W3 Model: GFB2 W3-3-1, GFB2 W3-6-2, No claims can be made against Geovent A/S in relation GFB2 W3-9-3, GFB2 W3-12-4 to loss of earnings or consequential loss as a result of defects on products from Geovent. -
Page 18: Spare Part List
14.0 Spare part list Art. No. Description Timer control panel GFB2 (mounted 92-214 as standard) 93-VNP-208 Solenoid valve 24V 13-729G Pressure switch 13-082 Alarm lamp 15-482FL Filter cartridge FT/18 10m² ePTFE 15-346 Plastic bags for collection bin 15-345 Plastic bags for collection bin Combination options for filter units and fans Typical Typical... - Page 20 HOVEDGADEN 86 • DK-8831 LØGSTRUP (+45) 8664 2211 • salg@geovent.dk...
Need help?
Do you have a question about the GEOFILTER GFB2 W3 and is the answer not in the manual?
Questions and answers