Karla Dubois GATSBY Assembly Instructions

What You Will Need
wHAT YOU WILL NEED
Step 03
Step 05
C.0 S I D E P A N E L
I. 0 B O T T O M P
WITH BOTH THE HEADBOARD (A) AND FOOTBOARD ( B ), USE THE REMAIN-
F.0 S I D E B R A C K E T x 4
ING 8 ALLEN HEAD BOLTS (I) TO SCREW INTO FOUR BOTTOM HOLES ON
I. 0 A L L E N B O L T S 1 " x 1 6
EACH OF THE PIECES. LEAVE THESE BOLTS LOOSE.
G.0 S U P P O R T B R A C K E T
J. 0 S C R E W S x 8
K.0 W A S H E R x 8
L.0 A L L E N W R E N C H x 1
F I G U R E 1
Care And Maintenance
PERIODICALLY CHECK YOUR BED FOR ANY LOOSE BOLTS AND SCREWS AND TIGHTEN WHERE NEEDED. IF BED IS DAMAGED, DO NOT
USE. CONTACT US FOR REPLACEMENT PARTS. SPOT CLEAN ONLY. AVOID EXCESS MOISTURE.
Step 04
STEP 05
A. QTY1
One Year Limited Warranty
TAKE THE HEADBOARD (A) AND ALIGN THE BOLTS
TO THE SIDE BRACKET (E) THAT IS ALREADY
DEFECTIVE PARTS WILL BE REPLACED WITH A ONE YEAR PERIOD FROM DATE OF ORIGINAL PURCHASE. MISSING PARTS WILL BE
ATTACHED TO ONE OF THE SIDE PANELS. ONCE
PLACED INSIDE THE HOLE, PRESS DOWN TO LOCK
REPLACED WITHON 30 DAYS FROM THE DAY OF ORIGINAL PURCHASE. KARLA DUBOIS WARRANTS ONLY NEW UNITS PUCHASED IN
THE BOLT IN PLACE. DO SO UNTIL BOTH THE HEAD-
IT'S ORIGINAL PACKAGING. THE WARRANTY DOES NOT COVER USED, SECOND HAND OR DEMOS AND IS NON-TRANSFERABLE.
BOARD (A) AND FOOTBOARD (B) ARE ATTACHED
TO THE SIDE PANELS (C). ONCE ALL PIECES ARE
ANY DAMAGED OR DEFECTIVE PART THAT RESULTS FROM NORMAL WEAR AND TEAR, ABUSE, NEGLIGENCE, IMPROPOSER USE OR
ATTACHED, BEGIN TO TIGHTEN EACH OF THE
ALTERNATION TO THE FINISH, DESIGN AND HARDWARE OF THE BED, OR THE ASSEMBLY OF THIS PRODUCT ARE NOT COVERED. THE
BOLTS USING THE ALLEN WRENCH (L).
SPECIFIC LEGAL RIGHTS OF THIS WARRANTY MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW ANY EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
B. QTY1
F I G U R E 2
IMPLIED WARRANTY LASTS.
CONTACT US
STEP 05
H. QTY2
PLEASE VISIT OUR WEBSITE AT WWW.KARLADUBOIS.COM THERE, YOU CAN FIND MORE PRODUCT INFORMATION,
WHEN FINISHED WITH ALL FOUR LEGS, FLIP OVER SO THAT
REGISTER YOUR PRODUCT, CONTACT US OR REQUEST REPLACEMENT PARTS.
THE BED IS NOW STANDING ON IT'S LEGS. PLACE BOTH
WOODEN STABILIZER (I) INSIDE THE STABILIZER BRACKET TO
SECURE THEM IN PLACE.
YOU CAN EMAIL OR WRITE
CARE@KARLADUBOIS.COM
KARLA DUBOIS
14001 ROSECRANS AVE
LA MIRADA, CA 90638
H O M E
SEE FIGURE 1
Set Side Bracket ( F ) on the Side Panel ( C ) as shown below in Example 1.
Place bracket so the two holes are against the Fabric. Next, place the 1"
Allen Bolt ( I ) into the two holes and �ghten using Allen Wrench ( L ) as
shown in Example 2. DO NOT OVERTIGHTEN. Repeat un�l all four
brackets have been a�ached on both the Side Panel (E).
x 2
A N E L x 2
SEE FIGURE 2
Use the Screw ( J ) and Washer ( K ), loosely screwing them into the four
holes in the middle of the side panel. The Support Bracket ( G ) will be
placed behind the washer. Once is is secured, �ghten the screws. DO
NOT OVERTIGHTEN.
A.0 H E A D B O R D x 1
B.0 F O O T B O A R D x 1
C.0 S I D E P A N E L x 2
D.0 L E G S x 4
E.0 B O T T O M P A N E L x 2
F.0 S I D E B R A C K E T x 4
G.0 S U P P O R T B R A C K E T x 4
H . W O O D E N S T A B I L I Z E R x 2
Step 07
STEP: 01 STEP 04
THE LAST STEP TO BUILDING THE GATSBY TWIN BED IS TO LAY THE
0
0
BOTTOM PANELS DOWN, SIDE BY SIDE, ONTO THE WOODEN SUPPORTS.
0 0
CHECK ALL BOLTS TO BE SURE THAT THEY ARE SECURED BEFORE
0
PLACING MATTRESS DOWN.
S IDE PA N E L W / B RA C KET S IN S TAL L E D
STEP: 02
E. QTY4
D. QTY4
Step 06
FLIP OVER THE TODDLER BED WHEN YOU'VE FINISHED
ASSEMBLING THE FOUR PIECES OF THE BED TOGETHER.
B O X C O N T E N T S
ONCE IT IS FLIPPED ON IT'S SIDE, BEGIN TWISTING THE
LEGS INTO THE SIDE BRACKETS.
wHAT YOU WILL NEED
A. H E A D B O A R D
B. F O O T B O A R D
C. A L L E N B O L T 1 "
E. A L L E N W R E N C H
I. W O O D E N S T A B I L I Z E R
BOTTOM PANELS
F. QTY4
G. QTY4
J. QTY8
K. QTY8
I. QTY16
L. QTY1
C. QTY2
I. 0 A L L E N B O L T 1 " x 1 6
J. 0 S C R E W x 4
K.0 W A S H E R x 4
L. 0 A L L E N W R E N C H x 1
H O M E
04
0 3 02